I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello
I want to know if we can wake up nrf52832 in sleep mode , from a command through an application on a phone via BLE. If its possible can someone please guide me to...
I want to add backtrace functioanlity in nrf52. I am using functions given in below link:
link text
But I am not getting library files for defining functions mentioned...
Hi,
I have programmed a BLE code.
In the code we are continuously connecting and disconnecting BLE connection.
The BLE connection is established for around say 1 sec...
hi,
This function is called on BLE Event when someone writes to RACP characteristic
What i woud like to know is, is it called from any ISR routine?
Or when BLE Event...
The radio mode 250Kbps is removed from nRF52832. However, by our test, nRF52832 radio can still work with radio mode 250Kbps with setting
NRF_RADIO->MODE = (RADIO_MODE_MODE_Nrf_250Kbit...
Hi All,
I have a question about the SPI pin number on nrf51 Dk.
I don't understand when i look into the pca10028.h file, i see this mapping:
#define SPIM0_SCK_PIN...
Hello,
I am trying to compile the example ble_app_eddystone with the SDK12.2 for the nRF52_pca10040_s132
While compiling with SEGGER I get the error
Compiling...
Hello,
I set up a project on the base of "BLE_APP_UART" to which I added header files and configured the sdk_config.h
Now I get these warnings during compilaiton:
...
Hi!
So I went from the Battery Service example to create my own service which went well and everything. Now I don't need a battery service, which is why I was trying to...
Hello,
i am working on Low current consumption project.
i have one question. what will be the good option to use the SPI or TWI ?
who have less current consumption ?
...
Hi, I want to ask some questions about BQ24090.
According to the schematic in the datasheet of BQ24090 , I have several questions below:
When should the led indicator...
I added the peer manager in my SDK11.0.0 application. I also have OTA DFU but everytime I boot into the bootlader, the first connection fails and I have to reconnect again...
Hi,
I am getting the "Couldn't connect Nordic_HRM" toast using the experimental project.
I saw the question but the answer there (sample code for selfie stick) is a very...
If I enable the Data Packet Length Extension and I enable the Connection Event Length Extension, having a connection interval of ~400ms I know that I can reach up to 251 bytes...
