I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
I'm using Nordic NRF51822 and the Segger JLink with the s110 Bluetooth stack active (correction: flashed on the chip, see below). When my code hard faults (say due to a dereferencing...
hi, I currently stuck in the follow section:
static void gpiote_event_handler(uint32_t pins_low_to_high, uint32_t pins_high_to_low)
{
if (pins_high_to_low & (1 << BUTTON_0...
Anyone to tell me where can i get the CDB file for nRF24LE01? I've downloaded the SDK and the nRF go Studio, but i still cannot find the CDB file.. Please help me to find...
Hello,
I'm trying to start softdevice on a custom board with nRF51822 chip and S110 device. The code hangs in SOFTDEVICE_HANDLER_INIT. It seems that EVENTS_LFCLKSTARTED...
Hello,
firstly I would like to say that I tried searching the forum for a post that has similar problems to my own. But I haven't (please tell me if i'm wrong) seen any...
Question: Can a nrf51822 acting as a server/slave message a client/master (iPad), that it has bonded with previously, to let it know that new data is available without having...
Hello,
I would like to experiment s120 on the evaluation board.
There are some examples but in nrf51/nrf51822/Board/nrf6310/s120/experimental.
Can I use it ? Or is there...
What are the correct PTX and PRX configuration settings for using dynamic payloads with auto ACK disabled? Can I just clear EN_AA and set EN_DPL and DYNPD for the pipe I'm...
Hello! I am working on a project in which I want to send stored sensor data to a smartphone whenever the phone is in range or at specific times of day.
Most of the communication...
Hi,
I am trying to get hold of version 2.1.0 of the dev kit for use with the sniffer. The dev kit is in stock at Mouser but they can't confirm the version number, but said...
I have developed the schematic of connecting NRF 8001 BLE chip with Arduino,the file is attached that contains the schematic. Can you please verify my schematic i.e will it...
Hi, I'm looking for a solution can make a ble device communicates with multiple 2.4g devices at the same time , is 51882 qualified for this? or just by combining both nrf8001...
Hello,
I would like to use the fifo common library but i have an link error. I don't understand that because fifo_app.h is included and contain the functions...
...
