hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
I checked the errata document for nRF52832 Rev.2.
In #182, there is the sentence of "Improvements as described in IN #105.".
However, I can not find the #105.
...
Hello!
I experienced the same errors as here and here when following the Eclipse gcc tutorial (7), but the solutions did not solve my problem.
I suspect this is related...
Hello ,
I use nrf52832 in my custom card, I developed everything on the develeppement kits nrf52, and when I merge to the custom card, I remerque that there is a huge consumption...
Hi Sir,
We have designed custom nRF52832 board in PCB design layout have 4 Pin connector VDD, SWCLK, SWD, GND. I know how to use nRF52832 DK for programming. But for other...
Hi,
I am using SDK12.3 and stack s132 with NRF52832. We have to store 3 variables in flash memory and keep updating it once BLE connection is formed with the phone. We were...
Hi,
I use nrf5_SDK_for_Mesh_v1.0.1_src SDK to debug mesh in SEGGER Embedded Studio for ARM 3.34. The projects are all based on NRF52832, but I want to debug it on 51822QFAC...
Hi,
I have been using the following parameters to flash program the example ble_app_uart_c_s130_pca10028 (SDK 9) but the problem is the it uses the S130 v1.0.0 softdevice...
Hi,
I have a newbie question. Is it possible to implement a POTS voice quality like an intercom system using Thread (assuming all the end points are using nrf52840 SOC...
We are trying to minimize the UART current in our product, so we tried some experiments on the PCA10040 board.
We noticed a significant current difference between SDK11...
SDK14.2.0 sd132v5.0.0 nRF52832
I've looked for a solution to my issue on the discussion forum, but can't find an answer. I am working with the buttonless DFU peripheral...
I have two nRF52832 devices. One of them I have been using for a while and the other is brand new. My BLE application will flash and run just fine on the old device but not...
Hello,
I read in your datasheet the follwoing:
"32.768 kHz synthesized from HFCLK (LFSYNT)
LFCLK can also be synthesized from the HFCLK clock source. The accuracy...
Hello,
in the Online Power Profiler , the current consumption increases, when the voltage is reduced. What is the reason for this?
Isn't there any documentation on the...
Hi
I need to capture a serial bit stream which consists of a sequence of 16 bit words, package them up and transmit over a bluetooth interface - it's a datalogger application...
