Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
Is it possible for a nrf51822 running s130 to advertise and scan at the same time?
I am trying to scan for other BLE devices using s130 softdevice, but cannot find an example...
Hi,
I have learned that you can change the MAC address on a device by using sd_ble_gap_address_set. However, when I press the sw2 button on the beacon (running a modified...
While reading about setting up nRF51 development environment on OS X , I came across the following:
Unfortunately the only way to erase
the memory is to do some magic...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
I've tried to set up my own BLE project as an exercise in understanding what's going on. It's going okay, with the exception that the device isn't advertising the data that...
I write PWR_UP using SPI and then read the Reg <0>. but I am not getting what I wrote.
Step 1 : Power ON using 3V.
Step 2 : Delay for 1 Sec to get into POWER DOWN MODE...
Hello,
On my custom board, I'm receiving chunks of UART data, without flow control, at 115200bps. Sometimes (its quite frequent now... sometimes after 10 chunks, sometimes...
I'm working on a PC application (using nrf51-ble-driver_win_0.4.1 API) to connect a BLE device and discover BLE services.
Today, I'm tying to connect the Nordic dev kit...
When discovering services using nrf51-ble-driver_win_0.4.1 driver, some ID are received with type BLE_UUID_TYPE_UNKNOWN. So I assume they are 128bits. I then retrieve the...
I downloaded the BLE beacon app S110 v7.1.0 to a nRF51-DK board. The current measurement pins were attached to a 10 Ohm resistor.
I observed the AC-coupled voltage at one...
Hi. We've got a chip with a code QFACA10. I am trying to find out if there is the internal pull-down of SWD line or not. It seemed that adding an external pull-down had positive...
Hi all,
I want to know the effect on power consumption of pins input buffer on and off, does there are big differences between them?
Another question is, since there...
Hey everyone,
when i was trying to compile i got this error which says
._build\ble_app_bci.axf: Error: L6200E: Symbol SWI0_IRQHandler multiply defined (by nrf_notification_manager...
