Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I am confused from reading the nRF52832 Product Specification on how to clear the GPIOTE port event (EVENTS_PORT) register?
On Section 21.2 (Port event) on page 158, it...
I am experiencing a difference in current between the example program during advertising between a IAR compilation and a GNU compilation.
The differences appear to be significant...
Hi,
Can the Nordic SoftDevices be consumed by a BareMetal ARM GCC compiled application?
Which compiler/linker flags are needed for the application to be able to link...
Hi
I am working on a firmware which can be used in serveral custom boards. While it works perfect in old sdk, I met the following problem when migrating from Sdk 12.2 to...
Hi,
I have tho following configuration: SDK 10, S110 and I'm using Segger Embedded Studio, single banker dfu.
I am able to program DFU and buttonless DFU; However, when...
Hi all,
I am using PCA10040 with nRF5_SDK_13.0.0 and using the ble_perpheral -> ble_app_uart example.
I am trying to stream data from UART to an android phone and the...
Hello,
I've been using the new power profile kit and I seem to be getting only 3 volts output as opposed to the previous versions where I was getting about 3.6 volts. How...
I was checking out the serial example using two PCA10040 evaluation boards. Most of the commands were executed successfully as mentioned in the link http://infocenter.nordicsemi...
Hi,
I'm developing a node based on the nRF52840-QIAA rev. B.
I'm using Eclipse Neon and GCC-toolchain for coding. Softdevice is S140 5.0.0.2 alpha and SDK is V14.2.
...
Hello,
I would like to be able to sample an analog voltage signal with a sample rate of approximately 250us (4096 samples/sec). I am using the SAADC example in nRF5 SDK...
We are trying to use nrfjprog.dll in a c# program to help us with manufacturing and quality assurance.
We are able to load and call the functions from c# and all the functions...
Hi! One of the designs still has the internal RC for the low frequency clock. Hardware and software turns out to be working okay, where system off current is ~0.4uA and sleeping...
Hi,
our BLE device has a hard current limit around 1mA. This is no problem as long as the BLE central behaves as "intended", e.g. iPhones use mostly connection intervals...
Hi All,
I am just play with nRF52 SoC.
We design small wearable device based on MDBT42V BLE module with nRF52832 chip inside. For lear we have nRF52 DK.
I work with...
