Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hello , I would like to know lifetime expectancy of NRF52832 IC. By lifetime expectancy I mean the amount of duration before NRF52832 goes non-functional. Please help me in...
Hi,
In disk_uninitialize function there are following lines of code:
if (m_drives[drv].last_result == NRF_BLOCK_DEV_RESULT_SUCCESS) { m_drives[drv].state |= STA_NOINIT;...
I have extend the light switch example to send message to the other node. I have refer This example to send message. But how to configure another node to receive the message...
HTU21D.rar hello there i am interfacing HTU21D with nrf51822. i am reading temperature and humidty from HTU21D. humidty register is E5. and temperature register is E3. now...
Hi,
I was trying to implement software UART for our product so I decided to use timer compare channels event connected to gpiote with interrupt. I want to toggle data line...
Hi,
Application: turning on/off a LED by toggling a GPIO pin using a timer and PPI. Important: the on-time of the LED must be very precise, i.e. the jitter must be minimal...
Dear Sir/Madam,
I have a sensor prototype board using nRF51822 for Bluetooth communication and I am now working on its firmware. I have installed MDK version 5.16 and...
Dear sir,
Sir i am using MDBT42V module. I want to know that whether the SCL & SDA pine are internally pulled high in this module ?
Regards,
Manoj Hiwarkar
Hi,
I have a problem where I am getting NRF_ERROR_RESOURCES errors 2 out of 3 times when sending notifications from my peripheral to my central. I think this is caused because...
I have designed a custom board with a TF325J32K7680 32KHz clock with +-50ppm tolerance, for the 32MHz I am using the CX2016DB32000D0WZRC1 with +-40ppm tolerance.
Simple...
Hi,
Within each example in the NRF5 SDK there are a number of folders including
arm4
arm5_no_packs
armgcc
config
iar
I'm having trouble finding an explanation...
Hello everybody,
I used SDK14.2.0 , S132 .
I keep the data from nus_data in the uint8_t array. Then I am trying to write the array with use fds_write.
My fds_write...
Hi, I would like to add source files to Projects with a reltive path. The reason being that I would like to have my own code in a cloud based directory and code from SDK in...
Dear friend,
To u se the Power Monitor for current profile measurement of nRF52832, I prepare the board by doing both of the steps described below:
(1) Short solder bridge...
Hi There,
I currently using PCA10040 development kit for my project. I tried to merge with \nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_blinky\pca10040\s132...
