Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
When i choosing among the 52832 and 52840, i found this table.
One point i am not sure, i believe the 52832 stack is already support Bluetooth 5, but why the table said...
Hello,
I would like to manage time (hours, minutes, seconds) on NRF52 chip: what is the best way to do it ? How to use as less energy as possible ?
At the first connection...
Hi all,
I'm new to Bluetooth technology and just start some test for indoor localization using 52382. But I find out that 52382 does not support the long range feature of...
Hello all,
I'm curious if anyone could lend some thoughts.
I'm just in the research stage and going through a few examples but getting a little overwhelmed.
I'm trying...
Hi,
I am using nRF51822, S130, SDK 12.3.0
Want to use is low power failure warning. using the following code.
However, when break on line err_code = sd_power_pof_enable...
I am currently using a CSR 4.0 dongle 8510 A10 chip on Windows 10 Creators update
I can get it to Pair with the nRF52832 in windows, according to windows.
I have a ...
I am upgrading an existing project that was working on SDK 14.2.0 with S132 5.1.0 to SDK 15.0.0 with S132 6.0.0. I'm using IAR 8.20.1, and have made the changes suggested...
Hi,
My aim is to transmit the beacons. iam using nrf51822 usb dongle and nRF5_SDK_12.1.0).I need to run E:\nrf1\examples\ble_peripheral\ble_app_beacon\pca10028\s130\arm5_no_packs...
Hi All!
I use SPI with ss_pin = NRF_DRV_SPI_PIN_NOT_USED. but seems it doesn not work properly.
in the file nrfx_spi.c , the following code exist to init ss_pin during...
Hello,
I am using a nrf51422 in my work. I am focusing on reducing system power consumption as much as possible.
Q. When a peripheral (server) starts advertising (and...
I am about to develop a Bluetooth Mesh network with the nRF52832.
With the PCA10040, i already able to form a Bluetooth Mesh Network, such that there is one client act...
Does anyone know where I can find a list of which phones/tablets support Data Length Extension (DLE)?
We are finding that many budget phones (e.g. Motorola G6, Samsung Galaxy...
Hi,
I'm using nRF52840 (rev 1.0.0) and Mesh 2.0.1 and SD 15.0.0.
I added FreeRTOS following the example "hrs FreeRTOS".
In FreeRTOS, the source clock (configTICK_SOURCE...
Hi,
I'm trying to use RTC2 as a custom timer using the RTC Driver, initialised as :
nrf_drv_rtc_t erx_timer_rtc = NRF_DRV_RTC_INSTANCE(2);
But when the BSP library or...
Good morning everyone,
I read a lot of threads in the last week on this subject, but so far I was not able to find a solution to the problem.
On a custom board we are...
