Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi,
I would like to know is there any shopping sites selling beacon modules that we can configure later based on our requirement?
I searched on few shopping sites where...
Hi,
We are developing a pretty complicated multi-threaded application on nRF52832.
Part of the requirements are storing a large amount of data over time (Megabytes)...
Hi
I am using gpio for input interrupt as below
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_HITOLO(true);
in_config.pull = NRF_GPIO_PIN_PULLUP;
...
According to PS, external reference min. voltage is 0.83V. However, I've experimented with voltages of about 0.2V and it appears to work. Specifically, I connected a voltage...
Dear all,
I am planning to develop a system which has the same functionality as N550M8CC SoC.
I cannot use directly N550M8CC module because space limitations so I am...
Hello everyone
I am trying to write to SDCARD with FATFS.
Data received from BLE and SAADC incoming data.
Writes every second.
The size is about 100 bytes.
SAADC is 1000...
Hi guys,
I wanted to try out the experimental "ble_app_att_mtu_throughput" on the newest nRF5240 DK. Using Keil, this project is to big for the free version. Since I knew...
Hi everyone,
I have one problem with the application timer. When I change the state of characteristic to the value of 1, the following code is executed:
err_code = app_timer_stop...
Just stumbled upon a few questions, which are hard for me to answer at the moment.
I wanted to do some throughput measurements with the example taken from SDK 14.2.0 mentioned...
What does the QSPI controller inside the nRF52840 do when the ACTIVATE task is started?
Does the ACTIVATE task result in communications with the external QSPI part such...
Hi,
I have a question about the UARTE peripheral.
is it possible to keep the DMA running and let it write to ram in a circular way?
I used DMA on the stm32 before and...
Hi there,
I'm a beginner with NFC and there is somethings I don't understand with the NDEF Messages frames. I have a the PCA10040 Development Kit.
I've seen this schematic...
Hi All!
I would like to implement the DTM nterface over USB VCOM instead of 2xUART (from examples).
Is it possible co-work USB driver (VCOM) and DTM from samples together...
