Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hello,
I have a project based on nrf51822 and SDK 10/S130. I have read about advertising mode and whitelist, but could not find my answer for my issue anywhere in the zone...
I added a new model to light_switch/server project according this , but how to test it working successfully or not?
I have tried to modify the light_switch/client to accept...
Hi，
When i do as the document say, i download the firmware to the development kit, and then i don't know which pin is the Tx and the Rx. How can i do all the function test...
Hello, I bought nRF51dk (pca10028) a year ago it was working fine last year in Segger Development Studio, now it gives build error "core_cm0.h: No such file or directory"...
Hi guys, me again.
Thanks for all the help before. I was developing me code with the example uart and now would like to control a LED with PWM output.
I have went through...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
I'm using the evaluation board PCA10040 with Segger Embedded Studio. It stopped working well and I get erroneous services even with the supplied examples (ble_app_blinky...
The device is broadcasting as "DfuTarg" and i want it to come out of the bootloader mode back to the application mode. Is there is a command i can issue to Secure DFU Characteristic...
Hi,
I'm modifying files in the NRF5_SDK_14.2 distribution and it is not clear to me which ones are part of the core SoftDevice libraries (and I, therefore, should not change...
(I know it has been asked before, but I thought I'd check in again..)
Has anyone had any success implementing the Dallas one-wire protocol on the NRF51822 - in particular...
Hello,
I imagine this is a pretty common and basic question but I couldn't find anything online.
Since the nRF52xxx chips are single-band 2.4GHz (and possibly sub-GHz...
I'm having trouble writing to a gatt characteristic using the python bindings for pc-ble-driver
Service discovery works fine, I managed to connect to a BLE server and reading...
I have a device that I need to control, that needs 2 different square wave signals of different frequencies (although they may be multiples of each other), one at around 4...
Hi all. I try to run capacitive sensor example on nRF52832 with my hand made capacitive sensor which I made according to this tutorial devzone.nordicsemi.com/.../.I connected...
