Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I deleted all the mega camera stuff as I want the MCU read image from another stm32, I successfully...
Hello,
We are developing a system that have the nRF5340 as a part of several MCUs, and we want to be able to upgrade both cores.
According to this: DFU for the nRF5340...
Hi All, I have a question regarding modem DECT phy API. There is a function nrf_modem_dect_phy_event_handler_set(nrf_modem_dect_phy_event_handler_t handler). I'd like to know...
We have successfully implemented the Template app on Android. However, the architecture of the multiple services and layers is somewhat opaque. Three questions:
How...
hi ,we have test the example of ble_app_att_mtu_throughput in nrf52840 ,the other side device is an android phone .
nrf52840 would freeze when the phone want to feature request...
Hello! I'm calculating the matching circuit with the antenna for nRF52832, but nowhere can I find the impedance value of the pins of the radio part, can you help me?
Hi,
I'm working with a nrf51822 based hardware which came programmed with some UUIDs and S110V7. Erased it completely, experimented with some non SD code first and finally...
Hello! I have a problem with checking the microcontroller nRF52832. J-Link does not connect to nRF52832, the screenshot of the Segger-commander window is shown below:
...
Bit of an odd question but Im dealing with a rather wonky SPI peripheral and its got me trying to sort some interesting questions due to its strange data protocol. Im using...
We are using the Android nRF toolbox v2.4.0 and have successfully implemented the Template app. The app will reliably connect with our device and functions well. The only...
Hi,
I was wondering if the SPI configuration for the p_config->sck_pin is correct. It appears that the clock is configured as output with input connected. Wouldn't this...
I am searching for long time how to inspect the prints in my code inside Segger , I went over many messages in this forum and nothing comes easy to me with this Segger thing...
Using Segger , only the BLE template is advertising,All other BLE apps such as BLE_UART, will flash the leds very fast but will not show on any Apple device on the Bluetooth...
We have an ISR parsing incoming serial data from the UART. When a valid packet arrives, I'd like to be able to wake the core from whatever low-power state is entered when...
That is probably an old topic, but after doing some research I could figure it out: calling sd_app_evt_wait() on my nRF5832 + nRF5 v11.0.0 SDK + s132 causes my chip to reset...
Hi
I've some troubles with the ble disconnection of S110.
Always when I call the sd_ble_gap_disconnect function after successful connected, the error code 8 NRF_ERROR_INVALID_STATE...
As I can see, I flashed Zephyr to Carbon 96 board, I don't fully understand the process,
I mean, I see .bin and .elf files but i don't see boot.img file, how do i make a...
