2025-06-13T08:43:42.649Z INFO Initialising the bundled nrfutil device 2025-06-13T08:43:42.652Z DEBUG Started watching devices 2025-06-13T08:43:44.400Z INFO Using the bundled...
We are in the process of finalizing the RF transceiver chip for custom protocol development.
Please suggest the suitable chip and any reference implementations available...
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
hai
in my application i am using nrf51822 . i have connected some sensors with the mcu. and i am collecting values from the sensors and this values are updated to the service...
In our code we use NV storage for system settings and calibration data.
I'm trying to understand when to open/close files and which structs to keep bwtween reads/writes...
Hello,
I'm using nrf51822/sd130/sdk12.1.0 and SOFTDEVICE_PRESENT defined.
But, I didn't enable softdevice.
I want to realize power save mode.
when I use __WFE...
hello there, i am using sdk11, i am using uart example. i am using nrf51 dk
SEGGER_RTT_WriteString is working. but
SEGGER_RTT_printf is not working. main.c
i have seen...
hello everybody,
i've downloaded the firmware files of nRF51822 beacon, but i couldn't find the source code. Does anybody know where i could find the source code of nrf51822...
Hello,
i try to use the nrfConnect (PC version) to update my devices via DFU. The DFU service is running on the device (update with Andoid nrfToolbox works without any...
Hi,
After finding that Windows doesn't like HID devices if they can't be bonded to, I've been attempting to add peer_manager and bonding into my application.
However...
Hi,
I'm working on a Custom Android app which connect to my NRF52 without any security.
This App is based on the UART demo App for Android, but I want that only my App...
I see that nRF52 SDK support the printf() , nrf_log_info() and app_uart_put() that can display data received on PC serial monitor, I'm wondering what's different/advantage...
I want to analyze the power consumption of connection parameter update procedure. How can i get a detailed description about the packet flow of it ? for example, the packet...
Hi all, I'm using sdk11.0.0 signed bootloader and I have custom board with dfu support. The custom board have device type ex:0x01 now I need to change device type to ex:0x02...
Hi all,
i need to read the status on my GPIO where there is a led.
I have configured it like a:
nrf_drv_gpiote_out_config_t configLed = GPIOTE_CONFIG_OUT_SIMPLE(true...
Hi. I'm using nRF51822, SDK12.2.0, S130 as multi-link Central.
#define SCAN_TIMEOUT 10
Time-out is working well when it is Single connection. After 10 second, it stops...
How i can see the performance like the Picture. is allways 0% and had also no time or calls in the execution profile. Breakpoints works.
But when i press F10 (Step over)...
