I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
I am using SDK 14.1.0 S132 for PCA0040 board
i want to combine the next two examples:
examples\ble_peripheral\ble_app_buttonless_dfu
and
examples\ble_peripheral...
Dear experts,
How is the UCIR protected against rewriting?
I would like to store some ID's which I want to be sure they cannot be erased or over-written once programmed...
Hello,
I can see s110 api commands as a web pages on infocenter.nordicsemi.com .
Is it an api list of commands manual in a document like pdf, etc.?
Thanks.
We are trying to configure the I2S peripheral for working with the ICS-43434 microphone ( www.invensense.com/.../) , but we are having a hard time fulfill the requirements...
The product spec is not clear, what is the maximum current draw possible from a 52832? Please assume ALL features are in use and fully enabled.
Thanks.
Hi Dev Zone,
I am going to communicate my nRF52840 Preview DK with an arduino shield. I am checking the PIN number. According to the information about the Arduino board...
Hello, I want to switch the functions between beacon advertising to connectable advertising.
In the code , it can be initial as a beacon advertising or normal advertising...
Hi,
I am running the ble_app_beacon example in nRF52 DK (PCA10040). I can see the nRF beacon in nRFConnect app - but not in the nRFToolbox - Beacons. After opening the app...
Hello,
I am using WT51822-S4AT based on the nRF51822 SoC and I am trying to program it with the ble-beacon example from the SDK. Looking at the DK documentation, I need...
Hi,
Device- nRF52832 (nRF52 DK)
SDK version 14.2
SoftDevice version 5
Segger embedded studio.
I am trying get the BLE working, unfortunately calling nrf_sdh_enable_request...
Hi, Everyone How to turn on 4 LEDs in BLE ? I am testing ble_app_uart on nrf52832 (softdevice s132). Try to blink the four LEDs on the board do. I have added to main() bsp_board_led_invert...
Hi,
I want to create a custom GATT service. So I duplicate the example from the SDK ble_app_blinky. Basically what I did so far is rename all the "LBS" (ble_lbs, lbs_p,...
Hello, I am trying to store microphone data from the Nordic Thingy by modifying the Nordic Thingy Android app .
The Thingy firmware encodes the digital microphone data...
Hi there,
First of all, I'm pretty new to this, so next question might be obvious to others.
I try to decipher a line of code, and the little Part is what puzzles me...
