Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Is the nRF24E1G obsolete?
If so, is there a drop-in replacement for the nRF24E1G.
We currently use the nRF24E1G in a product and have heard that it will no longer be produced...
Hi, I use IoT sdk with my iPhone to get current date and time, date comes in ble_cts_c_evt_t structure, how can I convert it to timestamp, I know that I have to subscribe...
Hello all,
As i want to lower the power consumption, may i know if its possible to connect the supply voltage of ntc thermistor to any gpio of nrf52832 instead of directly...
Hi,
I'm using the NRF52840 Preview DK and want to create my own BT stack with high throughput between NRF52 and other BT devices.
As base I'm using the ble_app_template...
Hi,
I followed the link, gnu-mcu-eclipse.github.io/.../ , to setup my debug environment before. I was able to view the registers. However, I updated my eclipse and the SVD...
I use the nRF52-SDK on an nRF52840 PDK, but if I start a scan request, I don't get the number of scanned channels back in the mlme_scan_conf_t.
I.e. mlme_scan_conf_t::unscanned_channels...
Hi! I need to understand the basic functionality of BLE Mesh.
Please see attached picture.
1. Is it true that a device (eg BLUE) through BLE mesh can communicate DATA...
Dear friends,
Software &Hardware: Power Profiling Application (a SDK example), S132 softdevice, nRF52832(PCA10040), Power Monitor. The measured average current consumptions...
What is the maximum sampling rate of nrf52832? I used the ppi on nrf52632 to collect the signal on gpio. After testing, it was found that when the signal on gpio is greater...
Hello all,
I want to built a coin cell powered thermometer with NTC thermistor.
May I know if I need to regulate the voltage from the coin cell or i can power the nrf52832...
I have a problem with the 802.15.4 software part of my nRF52840 PDK. I wanted to replace our current 802.15.4 hardware parts from TI with the new nRF52840, due to the lack...
Hello. We are now starting our review to customize code for the pending use of the Nordic devices in low power mode. Have a mix of Nordic kits now. Using the nRF52832 (PCA10040...
Hi,
I am trying to implement buttonless DFU by following the ble_app_hrs example provided in the SDK and modifying the bootloader (nRF51_SDK_10.0.0\examples\ble_peripheral...
