Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
Hi,
I am trying to secure OTA in nrf51822 board.
For that trying to build bootloader file available in SDK 12.2.0 version at location nRF5_SDK_12.2.0_f012efa\examples...
Hello,
I'm working on a project for which I would like to interface bno055 with nrf51822 smart beacon using i2c/uart. Basically the beacon must extract sensor values from...
With calls to these functions:
nrf_drv_gpiote_init()
nrf_drv_gpiote_in_init()
nrf_drv_gpiote_in_event_enable()
I have a handler (interrupt) routine that services a CAN...
I want to create a whitelist on the Central device. Because there is a lot of peripheral devices around and I just want to connect one peripheral device. First I register...
We have been recommended to use RIOT OS for our application and have been going through the tutorials but it seems that accessing the GNRC API for low ping ip communication...
Hai
i am using mbed to program my nrf51822. i need to implement bonding in my application. for that i am using securitymanager. and i have changed DEVICE_MANAGER_MAX_BONDS...
I am facing the same issue regarding to this post "Custom Service Issue - devzone.nordicsemi.com/.../".
At least i could figure out the IRAM1 start and size as explained...
Hi there!
I have been working with serializer and have the below issue:
I am using sd_ble_gatts_hvx() to transfer 20 bytes in burst until I get an error (TX buffer full...
Hi all,
first I have to admit that I'm a total rookie in "electricity". I know BLE software-side but just started to learn the hardware stuff.
I just received my PPK and...
by writing servals data into flash ,the data is always is 0,
void fstorage_test(void)
{
ret_code_t ret = fs_init();
if (ret != NRF_SUCCESS)
{
bsp_indication_set...
HI,
I am using nrf52832 with softdevice 132. Using SPIS1 to get the sensor datas from nrf to AARDVARK for calibration. Whenever I send the data's from aardvark(using AArdvark...
Whenever I try to flash the device in keil, I get a no Jlink device found. I get a similar message when trying to connect to the device via Segger. nrfGo Studio just does...
hello:
i want to use pwm in SDK9.0, in my project ,i need to send a cmd to nrf51822-QFAA,and then it control the motor on ,and with this cmd ,i should contrl pwm to let...
Can I control the music player by simulate a hid device
now our customer ask for a new function--use bracelet control the music player>> last next vol+- ...
but the app...
Hi,
I am trying to develop the ble_app_template project into a custom ble application.
Where is says
/* YOUR_JOB: Declare all services structure you application is...
