Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I have done erase all thing.
But in the second step, I am getting following error.
nrfjprog --program s132_nrf52_3.0.0_softdevice.hex
ERROR: The --family option given...
Hello,
I'm following the steps listed in the nRF5_IoT_SDK documentation and would like to connect the nRF52 to my Raspberry Pi 3 router. I have the RPi3 enabled for 6LowPan...
Hi,
I have exactly the same problem as in question devzone.nordicsemi.com/.../
but I can't find the solution.
When I erase all from memory, debugging works. If I flash...
Hi
We have been able to set LE authenticated payload timeout via the following functions:-
ble_opt_t opt = {0};
opt.gap_opt.auth_payload_timeout.conn_handle = ValidHandle;...
Hi there,
I am currently using nRF52832 to communicate with a digital sensor ship. The sensor chip generates an interrupt every time when data is ready to read via SPI...
Hi,
I would like to comment that your documents and files are not arrange in the proper order. Kindly please give attention in order to arrange the documents and files...
Hi,
My NRF52832 runs into the hardfault handler when the sd_ble_gap_conn_param_update() function is called.
I copied the BLE code from the ble_app_template_pca10 project...
Hello,
The Infocenter SDK documentation provides the memory layout used by different SoftDevices: infocenter.nordicsemi.com/.../lib_bootloader.html
Is it possible to use...
Can i process coap and adc data on nrf51 board , so that, based on that system will take decision like turning on/off fan or light etc?,if yes then what is the code and can...
I am confused about the lack of softdevice information for the Gazell examples. I am looking at SDK 10 now having first tried SDK12 before deciding to stay with 10.
As...
hello everyone:
i use interrupt to handle button.and when i init it,the power is increase about 200uA. i think the
interrupt will not increase the power
void gpiote_event_handler...
Hello,
I use the arm-none-eabi-toolchain and have a problem when I am linking.
When I make my project, I get the next errors
path/to/spi_handler.c:180: undefined reference...
Hello,
I am trying to test the BLE example named "Current Time Application" located at ble_peripheral\ble_app_cts_c folder. But i can't find the cts_central.ncs file in...
hai
i am using mbed to program my nrf51822. in my project i need to store some data in flash memory . now i am able to store it using pstorage.h . but when i enable bonding...
