Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
i am using nrf52832 dk. i am trying to change the flash address from 0x000 to 0x0002000. But i can only flash it to 0x0002000 if softdevice is already present on controller...
Hello,
I want to clarify one thing related to the limitaion in SoftDevice S130 V.1 of L2CAP_MTU size by 23 bytes. Is any way to extended it?
Because I see that changes...
Hi All,
We are trying to flash our custom NRF52832 board using NRF52-DK+nrf studio. With the same setup that's suggested by devzone.nordicsemi.com/.../
However, from...
Hi,
Recently i have moved to a much newer version of the SDK and have replaced my uart driver with the new ones, from SDK 12.7. The uart is between two nRF51422s one with...
I did not use softdevice;
//this my code
void SysClk_LFInit(void)
{
NRF_CLOCK->LFCLKSRC = (CLOCK_LFCLKSRC_SRC_RC << CLOCK_LFCLKSRC_SRC_Pos);
NRF_CLOCK->EVENTS_LFCLKSTARTED...
Hi, i just got the tutorial "Getting started with nRF5 DK" with a NRF52DK to run with IAR Embedded Workbench. Unfortunatly i'm not able to set a single breakpoint in the debug...
Is there a way to increase the size of the random number pool, and does the pool refresh periodically, or is there a way to manually trigger a refresh of the pool.
Our application...
Hello Nordic Semiconductor team,
I read about the new softdevice S132 v4.0.2, it says that "Concurrent central, observer, peripheral, and broadcaster roles with up to twenty...
I connected a Classic Bluetooth Device on my PC through by Bluetooth.
1-)I saw this message:
That means "Bluetooth Services Configuring"
2-)I saw this in device...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1.
I made boot secure and application as below.
boot.hex, application.hex
Then I made setting file as below.
nrfutil...
Hi. I'm using nRF51822AC, SDK12.2.0.
I just started trying priphral function which provides multi link(Max. 8 links).
Which example code can I refer?
I hope your...
I have a scenario in which hundreds of beacons are advertising. I want to know whether an observer can observe all the beacons or not. I have done a lot of search on this...
