Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
We are using s110_nrf51_8.0.0_softdevice.hex soft device and nRF51 SDK v10.0. We have below questions in case of soft device assert scenario.
In what scenario's soft...
Hello,
I am working with the example of PDM example on the nRF52832.
And over this I would like to use the drv_speaker. I put all the files from the Thingy 52 example...
On a system using an NRF52832 with S132 softdevice (without no external LFCLK XTAL), in low power mode via sd_app_evt_wait() - we see a nominal current of ~3uA with a periodic...
Hello Nordic,
Can you share pdf of nRF91 sneak peek presentation.There is an audio problem on video.
Best regards,
Marcio
www.nordicsemi.com/.../Low-power-cellular-IoT...
hi team,
i am having a doubt. i had created a service for connection interval which is 0x1528. with read and write properties. in that we can set value from 100ms to 10240ms...
I would like to ask for any information regarding the near-future plan for the nRF SDK for Mesh.
Are these features planned? And if so, when would they be implemented?...
nRF52832
There are three ways of working with the clock registers, a hardware access layer macro set, the nrf_drv_clock.c/h, and direct register access.
What is the...
I am implementing Device Firmware Update using BGLib on C# using BLED112. When i am writing on the DFU Data point on Peripheral (which is a Nordic's nrf51 chipset), i need...
hi,everyone.
version:sdk10.0
i know the nrf51822 system running order is: softdevice->bootloader->app.But i have a question when i am reading bootloader. If the program...
I have a question about the wait_for_flash_ready routine in the nrf_nvmc.c file.
static inline void wait_for_flash_ready(void)
{
while (NRF_NVMC->READY == NVMC_READY_READY_Busy...
Hey,
I have my nrf 52 dk and nrf connect 1.1.1.
I have soft device v3 on my nrf 52.
I connect my board into my computer, NRF connect recognizes my board and gives me...
Hello,
4 of 5 times when i want to connect to my firmware using RTT the firmware crashes.
Commands that i use are:
terminal one: JLinkExe -if SWD -device nrf52 -speed...
Hello ,
I'm using nRF52810 with SDK 14.1 base on ble_app_uart example. where i am continously receiving the GPS data via UART. i am putting my GPS module in sleep mode...
Hello,
My setup is: ble_uart_app example, custom board with nrf51822, sdk 6, s110, nrf connect for pc.
I am advertising with my peripheral device. Whitelist is being...
