I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hi,
I have started your tutorials and just complement this one. devzone.nordicsemi.com/.../
Now when I tried to download other programs on the development kit, I get...
Hi,
I have wierd experience about using float32_t.
This is my test:
When i use operations on float64_t i got:
0.0001s MAIN:INFO:init_finished
0.0001s MAIN:INFO:loop...
I have a program which uses two timers to flash an LED, alternating between flashing once every 5s for 15s, then once every 0.25s for 15s.
If I run this on the nRF52-DK...
Hello,
I am new to nrf51822 BLE. I am using MDBT40 (nrf51822 series). Complete project is powered by 12V, 2500 Mah lithium ion Battery pack. I want to monitor battery level...
Hi,
I know how to OTA a ble device, but how do this on a ble master?
Is there any nrf tool can OTA a ble master ?
dev environment:
SoftDevices:S130 v2.0.1
sdk: nRF5_SDK_12...
Hi,
we are using a ISP130301 module from Insight SIP (containing a nrf51822CEAA ) with a low power acceleration sensor ADXL362 , connected via SPI. SoftDevice is s130_nrf51_2...
Hi,
SDK: nRF5_SDK_12.2.0_f012efa
No softdevice
Example: nRF5_SDK_12.2.0_f012efa\examples\peripheral\radio\transmitter\pca10040\blank
and receiver.
I have running...
Hello,
I am using nrf51 and firmware is ble_app_gls. I have modified my code to work for dfu as well.
I am getting error as follows
.\_build\nrf51422_xxac.axf: Error...
I try to integrate the CoAP Server and TFTP DFU example code, and it works well.
[ENV]
IoT SDK v0.9.0
nRF52832 DK
According to the specification, the MTU...
Hi, dear support team,
I program the softdevice(S110,v7.1.0) to the nRF51822 devices(our product) by nRFgo Studio v1.21.1.3.
The nRFgo Studio shows a error message as...
Good afternoon.
I have 2 boards NRF51:
One as beacon (SDK 9), use example code "nRF51_SDK_9.0.0\examples\ble_peripheral\ble_app_beacon".
The other as...
Hi,
I have a problem using Secure DFU Bootloader available in SDK 12.1 on nRF51822_xxAA SoC.
Initilaly i was using nRF51 DK board and Secure Bootloader example in SDK...
Hello,
In our application, we do not use the antenna at Pin30.
However, in Nordic's Reference design in Github, even the simplest design (nRF52832_qfaa_dcdc) has an...
Hello,
Can I interact with the internal device of the nRF52 DK (PCA10040) while an other nRF52 connected through the P20 (or P19) connector?
The JLink tool has a "device...
I implemented an application to advertise indefinitely with APP_ADV_TIMEOUT_IN_SECONDS set to 0 and it works just fine. Now I want to
have a time out and set APP_ADV_TIMEOUT_IN_SECONDS...
