Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi all ,
I am beginning with DFU . I complete bootloader_secure_ble and can update new firmware (application) to my NRF52832 kit via Android . And now, I have 2 kit NRF52...
hi team,
i am wondering that lot of questions regarding gps and wifi interface with nrf52 is there. why nordic is not supporting with libraries and examples for gps and...
Hi there,
I read that the nRF52840 has a maximum data throughput of around 1.3~1.4Mbps . I also read that when configured as a central it can support up to 20 concurrent...
Hello,
Can anyone point me to a good example for Polling mode using serial library?
I'm looking for an application in which I can poll the serial port for data. I went...
I'm investigating the flash usage by the peer manager to store bond related data. While I haven't had a chance to fully investigate how the FDS and fstorage modules work,...
Hi,
We have a need to have a Nordic app for nRF51822 which both serves as a beacon and also offers a connectable service.
It's my distinct impression at present we cannot...
Hi,
My setup :
nRF52832
Soft Device S132 v5
SDK14.2
My use case involve me to send data to to a central device at 50 meters. I need to send only a small data...
Hello everyone :) , I work on a project initialy configured for a PCA10040 board and I would like to use the debug with my PCA10056 board but unfortunatly the debug doesn...
Hi
For some reason I get stuck in softdevice at 1EA7A when a send some random data to my phone also I notes that function sd_ble_gatts_hvx return 3401
PC = 0001EA7A, CycleCnt...
I am trying to connect thingy as peripheral and many smartphones as central but i can connect only one smartphone by using thingy at a time.Is it possible to connect many...
[References]
In page 234 of nRF52832_PS_v1.4 it says "In both modes, the TIMER is started by triggering the START task, and stopped by triggering the STOP task."
In this...
I am trying to add a custom service to support a communication path in my project. The Nordic UART example gives a good place to start so, using that as a template, I have...
Hi All:
i met a trouble.
i want to implement a function that i can restore mesh device by uart cmd.
so , i add uart to light switch service demo, when i recive a cmd...
Hi,
I tried the BLE Uart example on my own nRF51 board, but after a few minutes the application hangs in the softdevice.
The board is one we developed, an FTDI cable...
