Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi,
I'm using the nrf_drv_twi driver (master) to communicate with a number of IO components, such as LEDs, buttons etc.
If my IO component does not respond (why is not...
I downloaded SDK 12.3.0 (seems to be it is the last supported SDK for PCA10028) and tried to use fats example, I changed pin configs to SPI's pins.
I also prepared my 16Gb...
Hi there,
I'm putting together a PoC board for a demo - in this case size matters and I've had to make some compromises for the sake of speed (which have increased footprint...
Hi,
After setting up constant carrier, how can one determine that it is working. With no modulation the receiver can't determine anything, can it?
thanks
Hi,
SPI use with SDK14.2.0 leads to very high power consumption (around 400 µA) on nRF52832 (QFAA). The same piece of code running with SDK12.3.0 has much lower power consumption...
We developed a device based on nrf51822.
We use SDK11 and module Device Manager to implement bonding.
We have received feedback from the user, that our deivice was bricked...
Hi,all :
I just want to know how to enable the nrf_log (in the ble example).The version of the sdk is 12.3.0 and the cpu is 51822 .Thank you very much .
On the nRF52810 is it posible to change the gain setting for the SAADC on demand? For example the SAADC is reaching its cap and then the gain is increased so it is posible...
I see the max for a BLE connectable advertising packet of 31 bytes. I am not sure if the manufacturer specific data which also can be up to 31 bytes is included in the overall...
Hi,
We have recently moved from using the nRF52840 PDK to a custom PCB. The custom PCB uses nRF52840 Q1AABB, while the PDK has Q1AAAA.
On the custom PCB, the code is getting...
Good evening,
I'm having some difficulties with the thingy52. I used it as the basis of development for the project and up to this point without major problems. However...
IARv8.x.x no longer seems to display the detailed peripheral register settings in debug mode under "View->Registers" as all v7.x.x versions used to do. In trying to determine...
Hi,
I followed this tutorial https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-characteristics-a-beginners-tutorial?CommentId=adb9d7e0-1bf3-49bf...
Hi,
I'm using a nRF52832, SD132, SDK14.2 on a custom board.
I want to use BLE for precision, my use case require me to perform at least 50 reading from the SAADC per second...
Hi,
I'm trying to understand the speed of the BLE communication. What I do in my infinite loop is a SAADC conversion then send the value to BLE (int16_t).
In order to...
