In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi DevZone,
I am Nordic beginner, I am using the Nordic SDK example code for my current project. Before using Nordic DK, I was using Arduino for this project.
There are...
I'm trying to enable the S140 softdevice on my nrf52840-PDK from NuttX. When I call sd_softdevice_enable(), it returns NRF_ERROR_INVALID_FLAGS, which is not one of the documented...
I hope, operating BLE 5.0 at low data rate will give us longer range in open space. So in an environment like a football field, where each player will have 5.0 operating devices...
Hello,
I tried to add the code of the bluetooth tutorial called "Bluetooth low energy Characteristics, a beginner's tutorial", with a code that measures the delay of two...
Hi
I am working on a design using an nRF24L01+ in a circuit also consisting of an ATMEGA microcontroller and a H-bridge motor driver driving a brushed DC motor. The whole...
hi all!
I would like to ask the DCDC and LDO two modes of choice. My product is a watch, it uses the cr2032 battery dropped to 2.5v by an external LDO to 52832 power supply...
Hi,
I am using nRF52832 development kit PCA10040 V1.2.1 2017:38. I am able to successfully run nRF_Examples\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral...
hi,
I am using PCA10040 v0.9.0 Nrf 51 DK.
In schematic I am not getting connection for programming connectio n .In sheet 4 of 5 at the USB Connector connection signal...
Hi,
I m trying to develop an linux-application running on node.js to communicate with a nrf52 device. I m using the noble-module ( noble ) and a usb bluetooth-dongle. ...
Hi,
Is it possible to connect nRF905 to nRF51822 via SPI, add ShockBurst code nRF51822 and then use alternately/simultaneously Sub GHz and Bluetooth communication?
I'm...
Is there nRF Connect or similar program that enables development of BLE applications for Windows 10 (using native BLE API - ideally universal windows platform)?
At a connection the call function app_error_fault_handler()
with parameters
m_error_data.fault_id = 0x01 m_error_data.pc = 0x14DBE m_error_data.error_info = 0x0
Is not...
I'm trying to configure UART functionality in my program, and in the event handler under APP_UART_DATA_READY I'm missing bytes that I should normally have received. The code...
Hi,
Is possible to program the nRF52832 with a target voltage between 1.7V to 3.3V? I'm thinking to power supply the MCU with a pair of AA batteries in series.
Thanks...
I am using the "Nordic Uart Service", example to create a simple serial console which allows a user to change settings such as tx power, advertising intervals so that different...
