Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi Nordic,
I have an nrf52832 device where I cannot seem to erase the UICR. I've tried the various erase options from nrfjprog (-e, --eraseuicr, --recover) and those seem...
I am trying to port a program over from Eclipse to Segger Embedded Studio. It is a C++14 project and I am having problems because the STLport library that is included in SES...
Hi:
Recently, I use the SDK --- "nRF51_SDK_8.1.0", the project is \Nordic\nRF51_SDK_8.1.0_b6ed55f\examples\ble_central, I modified the project to notify the data periodically...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
The default SDK v14.2 PCA10040e (nrf52810) ble_ap_templete compiles to 131.7 KB Flash in SES and 34 KB Flash in Keil. I would think would have both project configured similarly...
I have looked over other posts regarding the iRAM and iROM settings for flashing firmware to nrf51822 devices but I am still lost on where to start. I've referenced the page...
I'm trying to create an automated script for deploying the command line tools with the segger Jlink driver.
I'm currently using the 9.6.0 installer with the following command...
So I reinstalled one of my Linux boxes (again) a few days ago, and one of the things I need to do to get all the development environment up and running (again) is get the...
Hi everyone,
I'm currently working on MAX30100 sensor and i need to read this sensor data with i2c, currently i'm able to read mpu6050 and 9255. However i don't have much...
Hi all,
My BLE device uses the NUS profile to send data to a connected smart device. At the same time it should also be possible to connect to a RPi/Linux based gateway...
I now use nrf52832 to do development, nrf52832 and mobile phones to transfer the data is relatively large, I would like to achieve For mobile phones that support BLE4.2, a...
Hi Everyone,
I have been experimenting around with the low power SAADC example in SDK13.
I am using PCA10040 dev board and I have programmed it to start/stop ADC sampling...
Hi,
We've been developing an peripheral HID over BLE using Nordic's SDK, connecting with iOS, Android, and Windows devices. (Board: nRF52832, SDK 14)
We've noticed an...
Using 2.0.0-1.beta on Linux Mint 18.
Have installed pyserial with: sudo pip install pyserial --upgrade --ignore-installed
resulting in:
Installing collected packages...
hi ;
now after i maked a successful connection between smart phone and nrf51822 and i could change the state of gpio pin 20 i find a new problem
i want my pin is still...
