When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
i am using nrf52832 dk. i am trying to change the flash address from 0x000 to 0x0002000. But i can only flash it to 0x0002000 if softdevice is already present on controller...
Hello,
I want to clarify one thing related to the limitaion in SoftDevice S130 V.1 of L2CAP_MTU size by 23 bytes. Is any way to extended it?
Because I see that changes...
Hi All,
We are trying to flash our custom NRF52832 board using NRF52-DK+nrf studio. With the same setup that's suggested by devzone.nordicsemi.com/.../
However, from...
Hi,
Recently i have moved to a much newer version of the SDK and have replaced my uart driver with the new ones, from SDK 12.7. The uart is between two nRF51422s one with...
I did not use softdevice;
//this my code
void SysClk_LFInit(void)
{
NRF_CLOCK->LFCLKSRC = (CLOCK_LFCLKSRC_SRC_RC << CLOCK_LFCLKSRC_SRC_Pos);
NRF_CLOCK->EVENTS_LFCLKSTARTED...
Hi, i just got the tutorial "Getting started with nRF5 DK" with a NRF52DK to run with IAR Embedded Workbench. Unfortunatly i'm not able to set a single breakpoint in the debug...
Is there a way to increase the size of the random number pool, and does the pool refresh periodically, or is there a way to manually trigger a refresh of the pool.
Our application...
Hello Nordic Semiconductor team,
I read about the new softdevice S132 v4.0.2, it says that "Concurrent central, observer, peripheral, and broadcaster roles with up to twenty...
I connected a Classic Bluetooth Device on my PC through by Bluetooth.
1-)I saw this message:
That means "Bluetooth Services Configuring"
2-)I saw this in device...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1.
I made boot secure and application as below.
boot.hex, application.hex
Then I made setting file as below.
nrfutil...
Hi. I'm using nRF51822AC, SDK12.2.0.
I just started trying priphral function which provides multi link(Max. 8 links).
Which example code can I refer?
I hope your...
I have a scenario in which hundreds of beacons are advertising. I want to know whether an observer can observe all the beacons or not. I have done a lot of search on this...
