Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Android nRF Connect app DFU is flakey on my phone, a Motorola Droid Turbo w/Android 6.0.1. I tried with a Moto X and it worked fine, but on my Droid it rarely downloads successfully...
I'm using 52832/S132 V2/SDK11. For the test I only send notification to central just to see how many I can send in each interval. I keep calling sd_ble_gatts_hvx() until I...
Hi, I am having some issues. Just getting started with the nRF51422, so forgive my being a bit "green."
Background: Testing with nRF5_SDK_12.3.0_d7731ad, Keil V5.18A on...
I was looking for a way to connect multiple nrf52832 via ble and connect the master to a smartphone app. Right now I'm focussing on connecting two nrf52832 through BLE. Can...
Hi there,
I see the "Error 133 (0x85): GATT ERROR" in the nrfconnect App with an HTC U11 Life with up to date Android (8.0.0).
I tested the nordic ble_app_uart example...
I am setting up the Power Profiler kit as standalone, no DK, measuring external target, also use the Segger jLink as interface. With the 2.0 software, it could not connect...
hello ,
can anyone guide how to add custom service and charactericteristic and receive data from nrf connect app using handler
i am using
board :PCA10040
nRF52DK ...
Hello guys!
We have a new project were will have to use dfu ota for a custom made application on a nrf51 beacon. Since the beacons use legacy dfu we want a way around...
Hello! I am trying to advertise two 16-bit uuid's and a 128-bit uuid. I set up advertising_init as such:
I declared the following structures:
where "SENS_UUID_SERVICE...
I am using Fanstel BT832 module based on nRF52832. I am using ' nRF5_SDK_14.2.0_17b948a ' with ' s132_nrf52_5.1.0_softdevice.hex '.
I am using this module as the BLE peripheral...
Hey Dear Nordic Devzone,
Here I am again, it has been a long time. Before I was working with the nRF52840 and Segger Embedded Studio. But as of now the company I am working...
i have programmed a arduino to send data(int value) on tx ,rx pin .How shoul i set up the nrf52 (the pin no of rxd and txd on nrf are p0.6 and p0.8).Which example should i...
Hi,
I'm looking into the reliability of the BLE connection from one nrf52 to another nrf52. I'm looking to understand a few things.
Once a connection is established...
