Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
hello everyone,
we're currently working with some nrf51822 beacons and throughout the project we recorded the antenna patterns of several of them. In the first batch we tested...
Hello.
I neet to write long characteristic value (250B). I use GATTS Queued Writes from example devzone.nordicsemi.com/.../ based on developer.nordicsemi.com/.../a00892...
Hello,
I am frustrated by a pair of nRF24L01+ communicating with each other, where all the Enhanced ShockBurst features are enabled.
The PRX is initialised as follows...
I could scan/detect Beacons, and I could update the configuration without any problem with the nRF Beacons app. The issue is that the configured Beacons are not detected in...
Hi,
I want to use the nRF51 dongle with the Master Control Panel.
I found in the nRF51 Dongle User Guide that the Dongle will run with the Master Emulator firmware, but...
I don't expect the Nordic engineers to know this answer but I'd like to hear from other devs out in BLE land...
Have any of you encountered truly horrible BLE PHY-level...
I am using S120 device to receive advertising from S110 device and need to get the exact time + sender's address information at Radio End Event.
I use PPI to start Timer1...
Hi,
I'v try to use the sd_power_system_off() and without successful.
The power consumption will be 200~230uA around.
My device:
Call the system off when ADV._TIMEOUT...
Hi
I am trying to make a ble central with s120 on a pca10001 board.
My problem is that it sometimes take a lot of time (up to 10 seconds) to find the client when i make...
Hello Nordic guys, help requested !!!
Error while connecting to USB port the new development boards, DK and DONGLE.
Error is " OS X unable to repair JLINK disk ".
...
Hi,
is it possible to use Nordic SDK with nRF51822 to have capacitive touch sensing with 2 dsital inputs, just as the mbed or avr library capsense?
MBED: developer.mbed...
Hi, i have a strange issue on connecting nRF24L01+ module to Arduino pro mini. I use arduino pro mini, nrf24L01+ module, 3.7V 6000mah battery and DS181 chip to measure temperature...
Hi,
When I start the TX sweep test with all 80 channels I get only 10 channels used by the RF.
Also power strength of the channels is modulated.
cf. attached frequency...
Hi
I am developing an iOS app that needs to communicate to an nrf51822(working in ble peripheral mode). The peripheral to which the app connect is selected using mac address...
hi nordic team：
I was wondering if the main program is too complex, and do not use the scheduler, and the connection parameter settings are correct. Whether because the...
