Hello
I'm currently mounting a LittleFS partition in the internal flash of my Nordic MCU. However, since data is saved regularly to this partition, I’m concerned that the...
Hi! I’m currently implementing a hook using mcuboot_status_change() inside MCUboot. I’m following the path defined by CONFIG_MCUBOOT_ACTION_HOOKS , and I’ve confirmed that...
Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hello,
I am trying to implement a Time-On-Air measurement with two nRF24L01+.
I set up the devices to work at 2Mbps, 3 bytes address, 1 byte payload, 1 byte CRC.
Both works...
I'm using the nrf51822 evaluation kit. There is low level access (via memory registers) the the 2.4Ghz radio in either a Nordic proprietary protocl mode, or Bluetooth LE mode...
Hello Nordic Semi,
We are using the nRF24L01+ for a remote switch application. We have a small transmitter button (nRF24L01+ layout as per datasheet with micro controller...
I have a problem within the following szenario:
I transfer data from my nRF51822 Peripheral to a connected Central (Android App) as a bunch of Notifications with maximal...
my project can't goto sysoff mode, (desktop2)( project based on mouse demo)
m_prw_mgmt_set_sysoff_timeout(DEFAULT_BTLE_INACTIVITY_DISCONNECT_PERIOD);//can't sleep here...
DEFAULT_BTLE_INACTIVITY_DISCONNECT_PERIOD is 3600//one hour
i can't wakeup if disconnect'time over one hour.
but i can wake up form com_event_advertising_timeout
my code...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Hi,
I am new using nRF51822 DK with the nRF6700 Starter kit. Downloaded nRF SDK and got most examples running fine including BLE examples with s110.
What I would like...
Hi, I am developing the nRF51822 BLE soc. I need using the authentication passkey for bonding. So far as I know that the passkey is generated by the SD. But I want to set...
I'd like to make a feature request for the S110 SoftDevice and the nRF51822 SDK. The problem centers around the inability to use passkey authorization on a device that does...
Hi,
I'm developing a BLE advertising sender and want to give the user the chance to change some settings of the sender with an iOS app. The user should connect/pair to...
I've been messing about with the random number generator just testing out events and interrupts. I got it working generating an interrupt but then I thought, NRF_RNG->EVENTS_VALRDY...
Im trying to figure out how to get started with the while development process to use the nRF8001. I have the nRFgo Development Kit and downloaded nRFGo studio and the nRF8001...
