Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
I can see for the same device on Android nRFconnect that the serial number in advertising data can be seen as here -->
The same device at same time on my iphone X with...
I using nRF52832 with nRF SDK 16.0.
I tested the SPIS example in the SDK.
I want to change the SPI Clock frequency to 8Mhz and read max 255byte at once.
How to set...
Hi
i m using Bmm150 magnetometer sensor. i m trying to read x y z values. However, im not able to obtain the correct magnetometer values. I'm getting 0000 as values in all...
Hi, I'm developing custom board with nrf52832
The problem is that when saadc returns negative value, all values that saadc returns after are max possible values from config...
PLease, could anyone provide me a code exaple on which i can learn how to use sd_flash_write & sd_flash_erease ? I tried to use them but keil give me this : .\_build\nrf51822_xxac...
Hello Dev Zone.
thanks for watching mt ask.
I need help.
I have 2 question.
1. I need use saadc continuous sampling
in SDK example, is it continuous Mode?
...
For RAM locations, I've looked at the getting started guide that discusses using debugging to find the RAM address. https://devzone.nordicsemi.com/nordic/short-range-guides...
I know one of nRF52840 SPI instances supports direct DCX signal drive but I can't seem to find any mention to this feature in nRF52832 so I am assuming none of its instances...
Hi Sir,
As check the ref. schematic of CKAA, the pin count shows 94.
But in the below table shows the pin count is 93
Is there a typo in the datasheet (V1.1)?
...
We are using nrf52832 and S132 Softdevice. The app starts from 0x26000 and we want to change to some other location may be from 0x27000. We could see that SD is using the...
Hello !
is possible turn off my system using sd_power_system_off when the Watch dog is enabled?
After I called sd_power_system_off my device is restarting and initialize...
I can not find where to change the default pins to connect the nrf52840 to the rpi over SPI. The default pins are SPI pin Raspberry Pi pin nRF52833, nRF52840 or nRF52811 pin...
I have begun using V1.2.0
It seems that I'm no longer to enter AT commands.
I've also tried the AT Command sample and get the same issue.
No problem connecting through...
Hello,
I am adapting the 802.15.4 wireless UART example from the nRF5 SDK 15.3 to also make scans and associate with a PAN coordinator. However i am having trouble with...
I have a time-sensitive block of code run purely by the CPU, not within any interrupt handler or peripheral. Part of the execution is getting interrupted, and so what I would...
