NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hi!
I am trying to use my own repo like described in the tutorial https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/nrf-connect...
I want make connection secure between mobile app and thingy52. What are the types for secure connection. Currently anyone can connect thingy without any permission.
I have setup zephyr development in an ubuntu 18.04 virtual machine. everything is working fine. but can't see the vcp. i disabled and enabled it in the jlink configurator...
Dear Nordic representative,
I would like to run qualification BLE tests on nrf52832 chip: - https://docs.zephyrproject.org/latest/guides/bluetooth/bluetooth-qual.html
...
Dear All,
In my application I need to switch on and off the modem using AT+CFUN=0 and AT+CFUN=4 respectivelly. My question is the following. Let's assume that the device...
SDK:V15
chip:52832
development kit:window+keil
In stm32,inder to use uart rx with DMA, we could easily use:uart Idle interrupt+dma.but how in 52832 while how many...
I’m looking at this example:
https://github.com/NordicPlayground/nrf5-calendar-example
which uses standard C function localtime(), but can not find neither in the example...
Hi devzone,
I learnt DFU through USB by performing the following steps:
1. build and run "secure bootloader usb" project with segger through J-link port J2.
2. flash...
I'm setting up a new project (solution?) for the nRF52-DK, using SEGGER, based on one of the examples in the SDK, and would like to put it under version control (Github, etc...
Hello , I m working on project to commande sim868 by serial (send AT Commands), so for the fisrt i would like to test the serial connection with an arduino to see what it...
We have developed our application on a custom prototype board with a nrf52832 (laird BL652) and it works great. We got in our production boards and all the IOs on the processor...
I have a problem while provisioning the dongles in a mesh network, which is faced by most of the people around. Right now I'm using the latest mesh sdk. Can you help me with...
I'm having trouble reading value from ADC. What I want is to read a sample and not set any timer, since I want to run it inside a timer itself and have the refreshed value...
I have designed a custom board using nRF52832. As per my understanding, we can configure any GPIO pin for UART communication. However, I am not able to configure the board...
Hello,
I am running into an issue attempting to add certificates to the device in order to facilitate HTTPS calls to our backend directly from the device.
Before the LTE...
