Hello community,
I recently was trying to evaluate the GC9A01 display from waveshare, I used the github source code as the base code to test this. Attached the link below...
I'm currently developing a USB dongle using the nRF52840 , and I'm facing an issue with inconsistent data reception intervals. I’d appreciate your insights on this problem...
I'm using a nRF52840 configured as Central and Peripheral, with nRF5_SDK 17.1.0 (I'm Not using Zephyr) for reading the Device Name from the Generic Service of a beacon. I...
On future revisions of the nRF52840 Dongle, and on future development hardware of a similar form factor, I'd recommend putting a debug connector that's compatible with the...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
I have 2 Channels with SAADC taking samples. They are configured to respond to BLE characteristics that have read and notify properties, each channel has its own characteristic...
Hi,
As in the Product Specification of nRF52, pin number 9 and 10 are configured as NFC pins. However, this setup is conflicted with our pin mapping for other sensors in...
I am trying to store a small amount of data on the nRF52832 with the FDS module.
I followed the following code found in another question:
devzone.nordicsemi.com/.../...
Hi,
We are currently migrating our codebase from SDK 13 to SDK 14 for NRF52832 based board. One major difference we see is that SPI transfer completion callbacks are not...
Hi Dear Nordic!
We have prepared 200 pieces of PCB (used nRF52840) to pre-test our Product.
Now we are waiting for nRF52840 IC to solder.
Is it possible to buy ~...
Hello,
I've just found the Zephyr project which provides very interesting features and many questions are rising in my mind, but I don't know if this is the correct place...
I want use the NRF52832's NFC Tag in a bracelet. I need to know when the battery of the bracelect
is out, can the NRF52832's NFC Tag still be readable? Like the UID of the...
Hi
I add code in nrf5_SDK_for_Mesh_v0.10.0-Alpha_src, and when it run the follow code
and the ret_code is 4, I get information from the follow code
it is NRF_ERROR_NO_MEM...
Hi everyone !
I'm working with nRF 52840. I've downloaded softDevice s140 using Keil. Afterwards, I selected the target to nRF52840_xxaa and then build the project of Heart...
Not sure I understand the sentence. Do you guys mean "enabled"?
PSEL.SCK, PSEL.MOSI and PSEL.MISO must
only be configured when the SPI master
is disabled.
infocenter...
Lately I've been getting randomly occuring hardfault in my code during heavy BLE traffic and Sensor data collection times. From the hardfault_implementation.c loop I see the...
Hi,
Is there a size limit for the vendor specific service UUID? It looks like it should be 16 bits but I can't set more than 4 bits in my code.
I am using the uart central...
Hi everyone,
I wanted to know if it's possible to change the length of a characteristic's value after it has been put in the attribute table. Reading some other answers...
I found two bugs in the SPI master driver and I'm posting the solution here to benefit anyone else that may run into these bugs. I apologize if these bugs are old news. I...
