Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
We need to sense temperatures in the upper end of the operating range, specifically in the 40C to 70C realm. We have three different units, and we are finding that the temp...
Hi,
We're evaluating NFC for our project.
I've been testing with a nRF52840DK - PCA10056 Version 3.0.2.
Using the antenna supplied with the Development Kit I am...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi
Do the latest sample apps (for example, Heart Rate) which do not required bonding behave as follows:-
make connection from iphone
enable notification
check...
We have done some test on how fast we can receive data from a BLE service, which is around 6KB/sec and this is all fine. This test was fairly easy to make, as we could just...
I have implemented my own I2C driver and I am getting issues with NACKs.
On review my code is doing what twi_hw_master.c is doing.
I then went looking for a Nordic sample...
We have developed and certified a module which uses the nRF24l01+. We spent a good amount of time tuning the antenna circuitry which has resulted in very good range... in...
Hi,
how to get into the bootloader mode without pressing any button, when some application is running? I also tried it with setting the NRF_POWER->GPREGRET but it is not...
I am looking for a minimalistic schema design using BLE for collecting data from i2c (twi) sensor and sending them over blue-tooth to the receiver. I need the following features...
Hello,
I would like to know if there are any restrictions in the amount of external memory (RAM, Flash) that can be added to a system using a nRF51822. In that case which...
Although there are some posts dealing with bond manager issues, I have not been able to find a similar issue. I am using part of the BLE code from nRFready Desktop 2 v1.0...
Hi,
i have some trouble with acting with the nrf 51822 ADCs. My Problem is that i have an Impuls which is 100 uS long and i have to measure it with 2 ADCs. I know that...
Hi,
What will happen when we press the service discovery button in the master control panel? do we get any event like BLE_GAP_EVT_CONNECTED? I couldn't find any detail regarding...
I'm looking for information to start developing BLE slaves with nRF51822, but I can't find any datasheets/SDK. Do I need to buy the Development Kit in order to have that?...
I have an issue with my keyboard working with the windows suface (on windows 8.1). Occasionally, the last character sent is repeated several times instead of one. I do not...
On the nRF51822, I see that by programming the readback protect register, one can prevent reading code regions 0 and 1 from the SWD interface. However, if one had access to...
Hi,
I just watched a webinar from the bluetooth SIG on how to create source code from the nRFgo Studio for the nRF8001. Is the same possible for the nRF51822? To create...
Hi,
We modified the ble_app_hrs code to work with accelerometer peripheral, and we have created some custom characteristics with custom uuid's. Now we need to set the device...
