I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
We are using nRF51822 Gazell protocol. We found that when host dbm is getting down to -61 or -62 dbm, the communication will lost. We had set it to +4db and use 250kb...
I have a question about how to build RSC (Running Speed & Cadence Service) ? especially using mbed compiler because I just found CSC (Cycling Speed & Cadence Service). like...
I am trying to add peer manager to multilink_central example on SDK14.1.0 based on the ble_app_hrs_c example. The code is running on nRF52832 and softdevice S132 5.0.
It...
hi,
I need combine to SAADC with BLE interface. The following is the code I have written. However, I'm unable to transmit information via bluetooth. Can anyone help me with...
Hi,
I have found this link devzone.nordicsemi.com/.../ . It seems you need to change SDK or softDevice to make it work with FreeRTOS. Could you please share more information...
Connecting to J-Link via USB...FAILED: Can not connect to J-Link via USB. I am using the BLE Sniffer 1.0 and when I star the Sniffer I get the error code that my software...
Hey guys,
I'm trying to make the FDS work with BLE and the scheduler.
But something doesn't right when I use the Softdevice and scheduler with the FDS.
Must I register...
Dear all,
I have nRF51 DK and I use mbed CLI to build my application that is simple mbed-os-example-blinky.
Also I have SDK11.0.0 and I built the ble dfu bootloader (...
Hi there
I did an upgrade of the bootloader from SDK 12.2 to SDK 14.2. I am using the nrf52832 chip. It is basically the same as the secure BLE DFU example from the SDK...
Hi everybody,
I was looking for a better way to update a data, like a 32-bit-word, without the need to erase the entire page. Part of this question is already been asked...
I was going through all the supported SDKs for the nrf52840 and in all of them, it is mentioned that the ESB and FreeRTOS support is not there yet. Could someone please let...
Hello, I'm trying to implement a buttonless DFU via ANT for a custom nRF52 board. I've got the 212 v4.02 Softdevice and I'm using the 14.0.0 SDK. I am able to transmit and...
Dear
i want to nrf52832 to collect accelaration sensor data（SPI communication 8MHZ）.
The sensor output datas per 250us,nrf52832 will lost the sensor interupt when 52832...
