we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi, I'm using blinky from the SDK12 as an example here with a nordic nrf51 DK (pca10028, onboard nrf51422) which I am using as a programmer with a custom board (with a nrf51822_XXAA...
Hi guys, just signed up here for some help.
I was learning how to develop a project with nrf51822 core chip. The one I'm using is this one . I also have a DK for the nrf51...
I'm attempting to change phy in a program based on the UART example and am following the same process used in the att_mtu_throughput for changing PHY.
Calling sd_ble_gap_phy_request...
Hi,
I'm using nrf52 + SDK11 + softdevice 132 2.0 and trying to integrate
the OTA dual bank bootloader. Using the nrfjprog tool I program the
softdevice + bootloader....
I am using the nrf52832 soc, and have a requirement to run the device in low power mode and using the timer with a timeout value in days? how can I do so?
Sample code would...
I want to read data, advertised by a bluetooth beacon.
I have made this work before with SDK v14 using NRF_SDH_BLE_OBSERVER() to register a handler function to handle BLE_GAP_EVT_ADV_REPORT...
As a complete newbie to this a bit of guidance would be really helpful to point me in the right direction.
I want to create a simple device with a couple of switches (physical...
Hi Nordic community,
I'm sending several packets from nrf51822 (custom board) to Android application. At the moment I want to configure the sensor by sending commands from...
hi,
I tried to recover custom nrf52 board by nrfGo stuidio,and it failed,the logs as below:
------------------------------------------------------------------------...
Hi All,
I'm using a sdk11 and i have started using the glucose profile example to use a peer_Manager.
I have modified it to have a just work behavior. It works correctly...
We have a potential application where we have to send data over BLE at 3kbps and store in external flash memory at 8kbps. The last memory accessed in external flash memory...
I have a NRF52840 and wanted to know, how much of a signal gets into another channel in BLE.
I am going to explain what I mean so there is no confusion :).
The Bluetooth...
Hi,
When I migrated the nRF51 project to nRF52, I got 67 L6218E errors.
I am not sure how to solve that kind of errors because I already added the related .c file to group...
I need to use an external RF amplifier. This needs two control lines, one for TX and one for RX.
I need some way to know when to change the state of the control lines. Is...
I'm noticing some irregularity on the SCL line coming from my Nordic 52832. I've attached a Saleae logic trace here. What are the potential causes for this type of behavior...
