Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Please refer to the link below. How can I configure the Commission Flow according to the requirements?
www.matteralpha.com/.../how-does-matter-qr-code-work
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
Hi everyone
I have installed the nRF Connect for VS Code Extension Pack later tried to install toolchain the latest is v3.0.2 it successfully installed but im not getting...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Hi,
I'm half way through the Cellular course on the dev academy and although I am able to connect to the Nordic and Hivemq publich brokers, when I attempt to connect to...
Hi,
I am trying to use the clangd extension with nRF Connect SDK, as it does a much better job than intellisense. I added
set (CMAKE_EXPORT_COMPILE_COMMANDS ON )
...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
Hi,
I want to use nPM1300EK、nPM PowerUP (official v2.1.1) profiling a chargeable battery, whose rated capacity、standard charging current is 2000mAh and 400mA respectively...
Hi,
I receive the following build error: "../zephyr-project-v4.1.0/modules/crypto/mbedtls/include/mbedtls/check_config.h:96:2: error: #error "Unsupported partial support...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi Team,
we are using two nRF5340 Audio DK kits to test LE Audio CIS example (unicast client & server).
kit1 nRF5340 Audio DK - act as gateway ( connected to PC/shared...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
