Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello everyone,
I want to measure current of the whole board, I follow the instruction of nRF52840 DK , which suggest not to use the USB connector to power the board.
...
I am using Rowley CrossStudio 4.4 to debug my project. I can program and step through the code just fine, but I can't seem to get any debug out put on the Debug Terminal....
(1) Production Programming using CLI:
We are entering pre-production for a design containing an nRF52810 (on Rigado BMD-330 module), and we need to know what the CLI command...
Hi,
I was referring the timer example code for PCA10040. I wanted to include the timer code in my ble peripheral code which uses custom GATT service. Can you help me with...
I see that the nRF9160 DK has both cellular and BLE capabilities because it has both a nRF9160 SiP and nRF52840 SoC. Wouldn't it be optimal to combine both cellular and BLE...
Hi There,
The attached image shows the part of the schematic responsible for the enabling of the QM14501. I was wondering if there was a particular reason that the mosfet...
Windows 8.1, 64bit PC
I have a nrf52840 app that works from "SEGGER Release 4.30 Build 2019101800.40379 Windows x64" on the DK 16.0.0, and from " nRF Connect for Desktop...
Hi there,
I want to implement the BLE dfu in nrf zigbee and thread sdk but there are no examples provided in the sdk and if i try to use the files from nrf 52 SDK for...
Similar to this ticket , we are no longer able to connect to Verizon using a Hologram SIM after upgrading modem firmware from 1.0.1 to 1.1.0.
I'm attaching a matching console...
Inside gps_controller.c
We issue the following instruction to begin searching for a satellite fix.
k_delayed_work_submit(&gps_work.work,K_SECONDS(CONFIG_GPS_CONTROL_FIX_CHECK_INTERVAL...
Hi,
We are atempting to get DFU over UART working in our project, but there does not appear to be a bootloader project in the 16.0 SDK for this configuration. What would...
Hello, I want to put extra authentication when device is preparing for boot loader. I found callback "ble_dfu_evt_handler". I think inside case BLE_DFU_EVT_BOOTLOADER_ENTER_PREPARE...
Hi,
I am using nRF51822, S130, SDK12.
Now trying to add a level of security with a static passkey, I have done the following adaptation to my code -
Added to void gap_params_init...
