Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
Hi triying to drive a Relay with Output but have tried every functon in "nrf_gpio.h"
this works with a LED perfectly :
nrf_gpio_pin_toggle(23);
in the main i configure...
I am currently working in the " ble_thread_dyn_mtd_coap_cli" multi protocol example.
Whenever I call printf my program crashes.
I think it has to do with the ble_nus service...
Dear friends,
I am trying to run the PWM in my project. I have:
added the PWM driver successfully (4.0.0-2.alpha, nrf_drv_pwm.c, nrf_drv_pwm.h) ;
set...
I tried porting app from pc10028 to pca20006 by copying the main file from pc10028 ble_app_uart to main file of ble_app_beacon of pca20006.I resolved all the #include related...
hey
I have a nRF51822 eval board and I want to use it as hid keyboard to send some media key
such as vol+/- play/pause, etc. I have used the example code ble_hid_keyboard...
Hi,
I develop a program using arduino primo,
and i want to layout a new pcb board with new nrf52832 chip.
The new chip may not have any bootloader.
What kind of method...
Hi
In our Nordic SDK ble_peripheral projects , It almost support following boards
1. pca10028
2. pca10036
3. pca10040 .
I want to port in pca20006
May I know...
I am porting a C++ project that was using version 6 of the SDK to version 14.2 (big leap, I know). I want to use all the new bells and whistles from the new SDK that makes...
I am using power profiler with nRF52840 SDK. And I have measured the current of the board. But I want to calculate the energy consumption of my program. How can I get the...
hi :
I want 4 channel PWM output, the following code doesn't work, I want to know where is wrong
#include <stdbool.h>
#include <stdint.h>
#include "nrf.h"
#include...
Hi,
I would like to control gpio pins in micro seconds with timer,
I know that it is very difficult to implement with only timer owing to soft device (interrupt handing...
Hey Dev zone,
I flashed my application onto my Nordic Thingy board (through Onboard Jlink debugger present on nrf52840 dev board), and can see some pretty colors (LEDs...
I am seeing some significant temp fluctuation for the temp sensor on the thingy to the tune of +-1 to 2 deg celsius. This is when placing the device in a closed, sealed container...