Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hello
we have a projekt with periperal "ble-app-blinky" und central "ble_app_blinky_c".
how to do:
when the "peripheral" battery is below 2.3V
then the led 4 on "central...
I'm trying to regularly change some advertising parameters ( ble_gap_adv_params_t.type ). The only way i can see to do so, is by stopping and starting advertising.
However...
I made a pulse oximeter product with nrf51822AC(base on SDK5.2.0 & S110 6.0.0), and implemented SIG GATT-based profile（PLXP+PLXS). Now we want to do BQB RF PHY testing to...
I have an example combining BLE, UART and SPI in which I use RTT to watch the startup process.
The SoC is nRF52 (BLE Nano2); building with armgcc.
This works ok when JLink...
Hi,
I need to send large data(about 200KB) from android phone to my custom board.
Connected like this :
Android Phone ->(BLE) -> nRF51822 ->(UART) -> Custom board...
Hey everyone,
I'm new to the Nordic/Thingy/Embedded world and was hoping I could get some hand holding to achieve a simple change.
I would like to change the Thingy...
Hi All,
I am working printer project where i will be using two boards , one is nrf51 dongle which acts as client(sends/advertise the data) and another is nrf51422 soc on...
Hello community,
I did a central device which is connecting with 8 slaves and this slaves are sending every time 8 bytes when they are connected. My set up is the following...
I'm trying to create a program that takes a stream of UART data at 115k baud streaming in and sends it over BLE as fast as possible. So far, I've
(1)Verified/ made some...
Dear Nordics,
If I add ble_nus service to buttonless_dfu example , it will reset after ble_dfu_init(). If I set
*p_ble_enable_params->common_enable_params.vs_uuid_count...
I am working on S140 on nRF25840. I am using the ble_app_beacon sample.
I want to set the advertising interval smaller than 100ms while using non-connectable mode. But the...
I am developing a product where I need to read a signal from an SPI ADC and send remotely to a receiver. This will be powered of a coin cell.
I see that the NRF51422 is low...
Hi,
I am trying to program nrf52 (on board ), but I keep getting these error:
$ nrfjprog -f nrf52 --program nrf52832_xxaa.hex --eraseall
ERROR: JLinkARM DLL reported an...
Hi,
I'm trying to connect and discover services of a BLE device equipped with a nrf52832. The device advertises correctly and i can see it on the nrf Connect app on both...
