Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
When factory resetting the flash storage, I delete all records, and then call fds_gc(). However, the page that's used for garbage collection still contains a copy of...
Invitation : The provisioner invites the unprovisioned device to send its provisioning capabilities information.
Firmware version from this examle: https://github.com...
Hi.
I've bought the nRF52833 DK and I want to use it with Mbed OS.
But I'm not getting it to work. If I compile the "mbed-os-example-blinky" program for target nRF52-DK...
Hello.
I would like to ask about writing data from Smartphone to Thingy. How to change characteristic using setOnCheckedChangeListener.
Is it correct way to change characteristics...
Dear people ,
nRF52840 and 15.2 version
I have uploaded the program ble_app_hts in my NRF52840. After which I uploaded ble_app_uart but I still get the "Nordic_HTS"...
I am trying to switch off the 3.3v power domain to save power.
I can disable it by using adp536x_buckbst_enable(false) in board_secure.c but when I try to use the same...
Hello
currently we are developing a hid bluetooth mouse using nrf52832 and SDK 15.3. We are using app_scheduler to send movement data to the host pc, but when we enable...
hi,
Is there any working PDM example for nRF52832? or can anyone give a sample initialization code for PDM with easyDMA using the inbuilt nrf_pdm_drv functions?
Regardss...
I am tried porting the USBD to mesh serial example according to usbd_ble_uart this days, and some functionality are test fine including Tx and Rx between Provisioner(USBD...
I teach high school robotics and after the BLE blinky program which works greata with mobile nrf-connect, I wonder what people think is the best, generic BLE
Central and...
Hello,
Can you please provide the input impedance or the S-parameter file of the impedance for the nrf52840 for receive mode, and also at tx power levels of -40dBm, 0dBm...
AD value and voltage conversion between the calculation formula
adc_config.resolution = NRF_ADC_CONFIG_RES_10BIT;
adc_config.scaling = NRF_ADC_CONFIG_SCALING_INPUT_ONE_THIRD;...
Hi, I have a few questions about the nRF52833 DK.
1. Can I fix an antenna array onto the DK to make it a receiver in Bluetooth 5.1 AoA applications? I can see that there...
My LTE Sensor Gateway sample connects via Bluetooth LE to a Thingy:52 and collects the flip state of the Thingy successfully. Now I want to replace the Thingy with the nrf52840...
