Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I've been noticing lately when running debugging on my code, a few minutes in it loses connection and says No Source Available for "0x01e054". I'm sure how to even figure...
I am trying to debug a custom version of the bootloader_secure_ble example but am running into FLASH space issues. The bootloader app does not fit into FLASH with -Og optimization...
Hello,
I am using Keil IDE for a while,and it is working perfect so far until, my code size gets bigger than 32K, I also decided to try GCC. I noticed GCC code size for identical...
nRF52832
SDK14.0
Hi,
I had two questions regarding Fstorage:
The Fstorage module works by having a queue of NVM operations. This queue only holds two types...
Hello!
I am using the nRF52832 with nRF5_SDK 14.0.0. with a JLink connection. My OS is Ubuntu 16.04.
After placing NRF_LOG_INFO() statements around my code, connecting...
Hi,
I am working on an application that needs to use pairing/bonding. I am incorporating peer manager into the project. I have included in Makefile paths the following...
I'm a little confused here...I have a basic main function which is turning on/off some GPIO and logging through SEGGER_RTT.
I thought that in order for that to work, you...
Hi,
I'm trying to get SPI working with an accelerometer (LIS3DH). I'm currently trying to use the nrf_drv_spi_transfer() function. See code snippets below.
// Initialize...
SDK14.0.0
nRF52832
s132
I would like to DFU the contents of the App Data section. In particular, I would like to erase the contents for a "factory reset" command.
...
I am setting up the DFU example to compile in Clion using ARMGCC 4.9 2015q3 and cmake. Everything compiled as it should and the DFU advertises. However, when trying to do...
hello there,
i want to send and receive data using spi and i2c protocol and i am using nrf51422 .how to interface which pins should i use to make spi and i2c communication...
I have an application that toggles an LED on P0.26 based on a timer and that's working fine. Now I need to add a few more timers so I decided to use the APP_TIMER library...
I am having trouble with an application where the NRF52832 operates several devices as a TWI master. What is even stranger is that I have been working on this code for a while...
I am developing a keyboard using the nRF52832 and example code(ble_app_hids_keyboard).
SDK is SDK14.
Korean/English change is not possible.
The specification I refer...
hello there i have basic question about BLE. what is difference between link layer and GAP??
i know about host and controller. but in both layer there is advertisement and...
