Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I am trying to use other functions within FATFS per example f_findfirst file on the flash and keep getting undefined reference.
I used the example application usbdc_msc...
we use custom 128bit uuid service and dfu,bas services
when setting uuid as custom 128 bit uuid in advertising_init function, it's base uuid is always based on dfu.
what...
Hi, could you please let me know if support for nRF5340 will be added to the "regular" nRF5 SDK package, or it will only exist in the nRF Connect SDK? Thank you.
I use a PA/LNA dur9ing advertising but would like to disable it during connection. I use the sd_ble_opt_set API which works fine to enable GPIO toggling. However to disable...
Hi, I'm trying to add buttonless dfu to my own application (unbonded). I have followed the tutorials listed below:
1, https://devzone.nordicsemi.com/nordic/nordic-blog/b...
I am trying to install the nRF9160 development environment on an additional computer. We have the system running on 3 computers now but are in the process of setting one up...
When I let the lwm2m_carrier library run through a full bootstrap/registration cycle on a fresh device, it generates and saves many bits of info in both NVS and TLS security...
I need to compute the checksum for a firmware image and I'm looking for suggestions on what works best.
I'm using SES and I don't see any checksum or CRC of the firmware...
In Beacon Why UUID is required ? Where exactly it will be useful ? I understand Major value Minor values , company identifiers values . it will difference the beacon location...
Hi guys,
i'm trying to deploy a BLE iBeacon on an Holyiot-17120 board. My code runs fine on the nRF52840 USB Dongle DK, but on this board works only when I've debugger...
Hi All,
I want to configure 64 MHz internal oscillator (HFINT) on my nRF9160 DK to reduce the wakeup time of nRF9160 chip from system-off mode. Is there any example available...
Hello,
I'm looking to be able to adjust PWM output frequency around 100KHz in 100Hz (or close to it) steps. I understand that no matter which method you use the implement...
Dear all,
I'd like to customize bootloader, I need more space so i modified flash address from example: FLASH ADDR (0x78000), SIZE (0x6000) to FLASH ADDR (0x69000), SIZE...
I am using the code above and already try it in the compiler . It should work but when I try to display in termite it only display .000 for microseconds.
Example
1987...
I used thingy s132 pca20020 sdk and i changed the code.
send data.accel.x, data.accel.y, data.accel.z data when data over the limit in swith case DRV_MOTION_EVT_RAW in drv_motion_evt_handler...
