Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I followed the issues from https://devzone.nordicsemi.com/f/nordic-q-a/54149/error-by-loading-solution-on-ses, which fixed the zephyr script issues, but was seeing the same...
Hi,
I have migrate to SDK14.2 the MPU9250 exemple from the peripheral folder in the nrf52-pesky exemples : https://github.com/e27182/nRF52832_pesky https://github.com/e27182...
I am using the nRF52840 DK with the s140 softdevice and am trying to copy the interrupt vector table to RAM to modify interrupts during run time.
I run the following function...
I am porting the eMD-6.12 firmware/library by Invensense for the part MPU9250 into the nRF52832. My toolchain is compiling through gcc allowing examples from SDK's to be quickly...
Hi,
We 're currently using an ARM SOM that will run Yocto Linux from NPX for our current project. We have the nrf52840 connect to this SOM via USB, and we want to be able...
I am using SDK V15 with an nRF52DK and Keil compiler.
I have difficulty finding an example to use a GPIO to drive a Piezo Buzzer. The requirement is very simple: use a GPIO...
Hello,
Is there anyone successful in communicating with an nRF52 based GATT server from a Windows 10 App? I’ve skimmed through the forum and do not come across any positive...
Hi,
I have an application that verifies a chunk of data and EdDSA Ed25519 signature against a remote public key.
The device application generates a random number, sends...
Hi,
I would like to add some custom sensor for Thingy:91 board. I notice that there are no GPIOs available to connect sensor to nRF9160 SiP? So do I need to connect the...
Hi,
Today I found I was unable to flash my nRF9160 DK. "west flash" fails with the error message "Installed nrfjprog is too old for the device. Please upgrade nrfjprog to...
I am trying to follow the section “Declaring custom cluster” ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v3.0.0%2Fusing_zigbee__z_c_l...
I've tried for two days to log back into the cloud service and just get the spinning angles. I tried to create a new account and the same. I was able to change the password...
Hi all, I would like to implement a fault handler in our nRF9160 based system to handle hard faults/unhandled exceptions by resetting the system, but am having a hard time...
Dear Nordic team,
I have a running NRF52 with a firmware based on the freeRTOS demo. To this demo I added the PDM Support Module and the TWI Module.
As soon as both sensors...
