Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
Recently, I was trying to established an application based on ble_app_hrs with PCA10028.
The MCU I used is nRF51822_xxac (256KB), S130 for softdevice and the SDK is...
After I add uart function to ble_example, I use app_uart_put() to send data,but data only one byte.What can I do?My board is nRF52-DK.SDK is nRF5_SDK_11.0.0_89a8197.This is...
Hi Team,
Iam working on nordic nRF52832 eval boards and trying to send a string from client to server over Bluetooth mesh using sdk v3.2.0.
i have created simple message...
Hi,
I am trying to increase the through put of the BLE peripheral device.
SDK Version-15.3, NRF52832 chip set
I looked into the example code ble_app_att_mtu_throughput_pca10040_s132...
Hi,
I am looking for support driving a Piezo bender for a car Alarm system. These alarms generally make multiple alarm sounds in a periodic changing manner. I am trying...
Dear All.
I'm using nRF52840 DK, 15.3.0 SoftDevice, Segger.
I'm testing DFU and have some question. and i'm begginer with all
I'm so s orry in advance.
First...
I have the nRF5 Mesh SDK "beaconing" demo compiled and running on my nRF52-DK. Is there a way to setup the beacon to be an iBeacon, so that it broadcasts a UUID, Major, Minor...
Hi,
I wrote a firmware using softdevice. How can i upload softdevice and firmware i wrote using nrfjprog command line tool. Also is it possible to locking firmware to prevent...
after update nRF Connect from 3.0.0 to 3.2.0 I started to get the error :
nRF52840 Unsupported device. The detected device could not be recognized as neither JLink device...
This is for the SDK nRF5_SDK_15.2.0_9412b96 and custom hardware.
I have a bootloader based off the example secure_bootloader_usb_mbr_pca10056 project. I want the application...
I'm using an nRF52832 with s132 and nRF5 SDK v15.2.0. I have a question about the tutorial devzone.nordicsemi.com/.../radio-notification The input parameter radio_evt of SWI1_IRQHandler...
Hi,
I have a customer interested in using the NRF9160 with a 1000mA/h battery.
They want to keep the board sleeping for 15 minutes, wake up and send GPS data position...
Hi,
Zephyr 2.1.0 will be released 2019-11-29, and it will support LwM2M Queue Mode which is an important feature for sleepy devices, see https://github.com/zephyrproject...
I am trying to modify the asset_tracker application to work without PSM mode since we cannot get PSM mode granted from the local network here.
My plan is to switch the modem...
