If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello,
Was programming two different boards today with the new 1.1.0 modem firmware.
Programmer reported the following for the two boards.
2019-11-21T21:10:34.297Z...
Hello!
Some time ago you seem to bundle sample 5 x nRF52832 to nRF52DK. Recently there was no bundled chips. Why did you change that?
The development and prototyping...
Hello, I tried to set up my nRF9160 with this tutorial and there is a problem: https://www.youtube.com/watch?v=jZQcmU3KIMY&t=216s
According to the tutorial, LED 3 and the...
I'm investigating the PDM peripheral on the nRF52840 and I have not been able to find out what the RATIO configuration bit actually does.
Presumably it controls how aggressive...
Hello,
I try to solve one problem with SYSTEM OFF and I still have no idea.
In my device I have one button switch and with this button I need to change characteristic...
I am using nrf52832 modules connected in mesh light switch example configuration from mesh V 3.2.0 i am unable to send a array over mesh i have gone through various posts...
I wanna know that, is latest SDK has demo example which will convert nRF52 SoC
to act like basic 2.4 Ghz transceiver (who should by default remain in Receiver mode &
switch...
Hi guys,
My question is really general: How do I reduce the TX Power of an nrf51822 BLE beacon?
The situation is the following:
1. I ordered this device: https://www...
We have a problem on our test system: it cannot communicate with our DUT on ATT level after 30 seconds.
Our DUT consists of a NRF52840 with SDK 16.0.0 and softdevice S113...
I have an issue with the NRF beacon code combining with the NRF rtc code.
I want to set up a bluetooth advertisement with an incrementing value. Therefore, want a timer...
Hello,
I am using ble_app_uart example in nRF SDK 15.2.0 in which I have included "nrf_drv_gpiote.h" and initialized gpiote as follows:
After making this change, the...
Hi Devzone!
I'm planning to integrate fpu_fft with ble_app_uart, and did it.
I wanna use IRQ of fpu_fft but I can't find where I should define fpu_interrupt_mode.
...
what is a last Online Power Profiler? this one ( https://devzone.nordicsemi.com/power/ )?
And I am wondering what is the model exactly I couldn't find the effect of connection...
Calling modem_info_short_get for the parameters MODEM_INFO_MCC, MODEM_INFO_MNC, MODEM_INFO_AREA_CODE and MODEM_INFO_CELLID fail. Call to modem_info_short_get works with MODEM_INFO_CUR_BAND...
