I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
I have a requirement where a handheld device containing a nrf52832 needs to be automatically paired to a switch (another nrf52832 device) when powered on, how can this be...
Hi triying to drive a Relay with Output but have tried every functon in "nrf_gpio.h"
this works with a LED perfectly :
nrf_gpio_pin_toggle(23);
in the main i configure...
I am currently working in the " ble_thread_dyn_mtd_coap_cli" multi protocol example.
Whenever I call printf my program crashes.
I think it has to do with the ble_nus service...
Dear friends,
I am trying to run the PWM in my project. I have:
added the PWM driver successfully (4.0.0-2.alpha, nrf_drv_pwm.c, nrf_drv_pwm.h) ;
set...
I tried porting app from pc10028 to pca20006 by copying the main file from pc10028 ble_app_uart to main file of ble_app_beacon of pca20006.I resolved all the #include related...
hey
I have a nRF51822 eval board and I want to use it as hid keyboard to send some media key
such as vol+/- play/pause, etc. I have used the example code ble_hid_keyboard...
Hi,
I develop a program using arduino primo,
and i want to layout a new pcb board with new nrf52832 chip.
The new chip may not have any bootloader.
What kind of method...
Hi
In our Nordic SDK ble_peripheral projects , It almost support following boards
1. pca10028
2. pca10036
3. pca10040 .
I want to port in pca20006
May I know...
I am porting a C++ project that was using version 6 of the SDK to version 14.2 (big leap, I know). I want to use all the new bells and whistles from the new SDK that makes...
I am using power profiler with nRF52840 SDK. And I have measured the current of the board. But I want to calculate the energy consumption of my program. How can I get the...
hi ：
I want 4 channel PWM output, the following code doesn't work, I want to know where is wrong
#include <stdbool.h>
#include <stdint.h>
#include "nrf.h"
#include...
Hi,
I would like to control gpio pins in micro seconds with timer,
I know that it is very difficult to implement with only timer owing to soft device (interrupt handing...
Hey Dev zone,
I flashed my application onto my Nordic Thingy board (through Onboard Jlink debugger present on nrf52840 dev board), and can see some pretty colors (LEDs...
