Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi,
Since I'm having a hard time understanding this through the SDK docs, I'll ask it here.
I'm currently using a BMD200 module (from Rigado) which uses a nRF5188.
...
I have a BLE-Nano v1.5 board with 32KB of ram starting at address 0x20000000 (til 0x20008000). However when I want to read a byte of the uper 16K (0x2004000+), I get a 'cannot...
I need to scan for nearby beacons.
This was featured in the mbed examples but does not seem to be described anywhere else
I am using SDK12 at the moment.
I found the...
hello
Now I use the nRF52832's board and I was measuring the current
But when the board's power is off and i measured, the current was flowed in the board.
Now i am using...
Hi!
I can't start project with OOB bonding. If I set settings like just works (MITM = 0, OOB =0), all works correct. But I need more security for bounding. For this reason...
This may seem rather pointless and stupid, but are there a set of APIs for asking the SDK it's own version, and getting it to ask the SoftDevice it's version?
Good morning,
Some contextualization first:
At my company we developed a product that is based on your NRF52832 microcontroller.
We are currently entering the certification...
I am encountering some problem in building eclipse project following the tutorial at devzone.nordicsemi.com/.../ .
Previously I succeeded in building with another simple...
Hi,
We bought several nRF52 DK with nrf52832 and intention is configure one of these as a gateway router to cloud via Rasberry PI.
I have IAR installed and I tested blinky...
Hello,
I've been all over the forum trying to solve my problem but I just couldn't find enough information.
I'm trying to set up notifications in my application, but...
Hello,
We're using SDK v14 and nRF52. To pass some data between reboots we're using the general purpose retention register. However, it seems like it's impossible to call...
I try to transfer the codewords from nrf51822 Dk board to a dongle board, while the dk board is PCA10028 and the dongle board is PCA10031, when I change the port numbers and...
I'm new to the nrf51822, i was connected led to one of the gpio pin of nrf51822 development board. In 1 minite i want to toggle led 20sec and remaining 40 sec in sleep. After...
The SDK 12.1.0 documentation for the FDS library says the following:
FDS_THREADS: If set, the FDS module can be used by multiple modules at the same time (for example...
Hello,
I am trying to measure the current consumption.
i could cut the SB9.
and i use analog discovery and measured!!
the picture is shown in below.
gyazo.com/b9f5607148cd9415ea7d1ee6ac644373...
