Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
I am facing the following error. I have referered light switch example and have included all the required configs in the prj_fota.conf file
CONFIG_NCS_SAMPLES_DEFAULTS ...
Hello,
I am working on a custom PCB that involves the NRF5340 and our first iteration of PCBs had soldering issues during assembly for the nRF5340. The nRF5340’s footprint...
Hello Nordic,
I am running a project, use the chipset is nRF54L15, I want to know if there is any USB dongle with software can be used to test BLE function of chip nRF54L15...
Hi everyone, I'm working on a project with Zephyr (v2.9.1) and I'm facing a compilation issue related to managing two SPI devices on different buses ( spi0 and spi2 ).
In...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
I am using NCS 2.7.0
i am running this build command from a terminal in VSC for the nrf/samples/bluetooth/Direction_finding_connectionless_tx sample
west build -p -b nrf5340dk...
HI,
I’m using nRF Connect SDK (NCS) v2.8.0 with the blinky example.nrf54l15dk, In the project, I configured the following in Kconfig:
kconfig
CONFIG_FPU...
Hi Nordic team,
My nRF52832 DK (PCA10040) was working perfectly until recently. Suddenly, it stopped getting detected by my PC.
Current Issue:
The board does not...
Hello Nordic Team,
I’m using the nRF9151 DK board in Surat, Gujarat, India with a valid Onomondo SIM card . I’ve followed the setup instructions as per the Nordic Academy...
Hello, I am trying to update the modem firmware to v1.3.7 using UART using the nRF modem bootloader API. For context, I am running nrf-sdk 2.9.1 and also using the SLM application...
Hi,
We’re working on a device using the nRF52832 and have DFU over BLE working correctly using internal flash. Updates work both via our custom app and the nRF Connect app...
Hi,
I believe 2M and 1M are OK to adjust, however, long range code added the extended advertisment, I am curious whether I can update these three PHY all together.
Thank...
Hi
I noticed one ticket says that "the following combination offers low power consumtion and high througput when needed :Short Connection Interval + High Slave Latency ...
Hi, I'm a beginner and I'm trying to run an LED blinking program. However, I'm encountering a device-related error.
I've followed tutorials and installed all the necessary...