Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
In the examples I see places where there is conditional code based on the #define HOST.
For example in function nrf_mesh_init() i see that the softdevice is only enabled...
Hello,
My team and I are experiencing a problem with our custom DFU Bootloader, which is based on the Experimental Bootloader Secure Serial example (SDK 13), running in...
Hello,
I'm reading on github.com/.../Android-DFU-Library that there is a support for higher MTU on DFU. Is there an example how i should test it?
I'm tring to increase...
Hi,
I have one chip use the VDD and GND pins on the PCA10028 and I use nRF current measurement pin monitor the current.
My question is:
Does nRF current measurement monitor...
Environment:
mesh SDK: V0.10.1
example: light_switch
compile and download IDE: SEGGER embedded studio v3.26a
Problem:
light onoff server and client can not...
I am using the ble_app_hrs_nfc_pairing example (sdk 14.0.0) on my NRF52840 with the s140 soft device. I am able to bond with my phone (Android 8.0.0 Oreo) by tapping the sensor...
Hello:
I need to disable an interrupt event outside the handler. During debugging when the nrf_drv_gpiote_in_event_disable function gets executed, the program seems to...
Hello , I want to save some data,even thought there is no power.eg. device name ,baudrate.I have try to use flash write example.How can i read or write data from a memory...
Hi all,
I have tried to mimic the LESC multi role example to my own app, but I dint have luck to pair it using LESC, MITM, and perform bonding and I received a SM_pairing_faill...
1、I down load the sdk about thingy52(about nordic 52832)，it is keil 5
2、the pack 《nRF5x-MDK-Pack-5-Clause-NOD》is down load,and it is install ok
3、but after steps2，when...
I am using nordic_sdk_7 with s120 softdevice on PCA10001 board.
I got BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST event from peripheral. Sending conn parameter update request to...
1、I have down load the thingy FW 2.1.0 which has three projects
2、I BUILD the 《pca20020_s132》，It is ok
3、and press the down load button in the keil
4、It shows download...
I am having problems implementing Device Firmware Update in Android. The specs of my development environment is:
Samsung Galaxy S7 Edge.
Nordic DFU API v1.5.1
...
Hi all,
I'm sending data with ble_nus_string_send() in a loop as shown below. If it returns an error it retries until it gets NRF_SUCCESS. I'm getting an error code 0x0013...
The DFU example given in SDK v12 is for secure bootloader. Hence, they are asking for public and private key. How to generate the key? Or is there any other way of disabling...
