Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
When initializing models from the models_init_cb it's useful to check the current configuration using the mesh config API. However, the returned values are always the default...
We are testing GPS capabilities for our hardware, using mfw 1.1.0 in the field. We have the following test conditions
The unit is ackquiring position every 5 min
the...
Hello,
We are trying to run the ble_ant_app_hrm example on nRF52840DK using nRF5_SDK_16.0.0_98a08e2 SDK and ANT_s340_nrf52840_6.1.1 softdevices (both latest as of today...
Hi,
I was looking for information about the MLME-ASSOCIATE primitives in the https://infocenter.nordicsemi.com/ . The section with the "MAC MLME Association API" title...
Hello. After I updated the firmware on Thingy 91, it no longer registers on the network via LTE - the LTE indicator in LTE monitor blinks between yellow and red, and I get...
Hello Nordic team,
I was wondering how to determine the QDID of our product. The relevant QDIDs are 101625 and 97989. I believe the latter should suffice but I am not sure...
Sir After Flash the code to board i am getting some info message in teraterm
below i have attached the image of the teraterm
Refereed link: https://infocenter.nordicsemi...
Hello Nordic team,
I'm using an nRF52840 with SoftDevice S140 version 6.1.1 which size is 0x25000 (without MBR).
My bootloader contains the bootloader code written at...
Hi to all,
Happy New Year 2020 !
I have developped an application with the nRF52832 ( nRF52DK ) and I use the SAADC for battery level every 2 hours ( no need of precision...
Using a NRF52840 running zephyr and mcuboot, the function nrf_cc310_bl_ecdsa_verify_secp256r1() is getting stuck in a loop.
I am using NRFXLIB v1.1.0
Looking at the disassembly...
Hello,
we developed 3 devices using nrF52840 and integrating your certified Zigbee stack.
in order to obtain the Zigbee Alliance certification, the laboratory ask us to...
hi , i need help!
when i conected to the phone(bonding)，then i disconnect from the device using sd_ble_gap_disconnect(),next the device advitising again; after that the...
If I develop a custom application where it will have several peripherals (with sensor function) and a central one.
Is it correct to use the same base UUID for all peripherals...
I am building a system with an external non-volatile storage (flash) which will be available for storing DFU image data received. I want to minimize the confusion and temporary...
i am able to connect two nRF52832 DK.
Now i want to send new Firmware packet over the air to another nRF52832 DK, which is connected with my DK.
So, can you guide me,...
