Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hi,
I’m working with the Wi-Fi station example on the nRF54H20 using SDK v3.0.0, and I’m encountering a critical issue when trying to bring up the nRF7002EK Wi-Fi module...
Hi Nordic team,
I'm trying to configure the GPIOs to operate at 3.3V using the nRF Connect for Desktop's Board Configurator tool (v0.3.10). The tool works as expected...
Hi,
I succeeded in implementing Channel sounding for multiple devices (based on previous samples). But now there is a little difference in how the data gets collected (buffer...
I have a project using BLE as a central on an nRF5340 to connect to several devices. For factory test I am being asked to implement something that can be used in the factory...
Hi,
I have designed a custom board, and I cannot get coexistence interface to work reliably. I don't get any errors, but I'm not able to connect to my board with BLE. WiFi...
Good day.
I`m very new to nordic chips.
I`m try to use NRF52832 as TWI master with OLED display based on SSD1306 with I2C.
And got this.
Yellow is SCL, Blue...
Hi,
I am trying to use the FDS for saving some variables and displaying them again later. I have downloaded the NRF52-fds-master sample code posted on github. However,...
i am working with mpu xx example given in nordic website. it seems code is working fine i.e. compiling and dumping into nrf52 DK, But not showing any output values.
i was...
I am using an Nrf51822 for a project. I looked in the datasheet and it said that there is a built in WDT for the chip. It also says that clocks can't be used while in systems...
I want to use in my project tft 1.8 display with st7735 controller. I'd like to use some based code but can find nothing except on infocenter nordic
As I understand there...
Hi,
I am writing a boot loader which does not need to use the soft device as the image is being transferred over an SPI interface.
I have merged the softdevice and my...
Hi
I suppose that Multiple connection to centrals is available from BT4.1.
Is it possible to realize bu S110?
If it is so, which version is available the specification...
Hello, I made some boards on nrf52832 and I was testing the PCB.
The test program is ..\nRF5_SDK_12.0.0_12f24da\examples\ble_peripheral\ble_app_hrs.
(I have downloaded...
Hello! Just got a few NRF51822's.. looking to just brodcast a few basic URL's.. if someone can point me in the right direction or maybe let me know where I can hire someone...
I work with ble_app_uart example and want to move uart init and event handler into separate file( e.g uart.c).
I just copy uart_init, uart_event_handler functions with some...
I am writing code that runs on a NRF51822 (to be less specific it runs on a Red Bear Lab BLE Nano). The board has a 32.768khz crystal on it that I want to use to wake up the...
Now I am sending data at 250 ms.
I'd like to send data at 80 ms.
Is this possible?
also,how much can it extend the advertisement interval to the maximum?
thank you in...
i am working with eclipse to program the ble_app_hrs but it is getting error "No rule to make target _build/app_trace.o', needed by nrf52832_xxaa_s132'. Stop" when it builds...
Hi,
In the newer versions of NRF 5 SDK (sdk10 vs sdk12), does the softdevice takes more RAM?
I am using nrf51822 (qfaa) and sdk 12.3. with softdevice s130_2.0.0.1....
I can't get my PCA10040 board to send serial data when connected to a FTDI USB dongle.
When the FTDI dongle is disconnected, and I connect my logic analyzer to the tx and...
