Hello,
I'd like to ask what needs to be configured to enable communication between two boards: nrF7002-DK and nRF5340-DK via another UART (e.g. UART1).
Please provide...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hello there,
Finally received my 2 DK's after developing my other 2 custom PCBs and not knowing how to program them without the arduino IDE and now I'm struggling to program...
There seems to be a bit over a bug with the freeRTOS example. If you add the Scheduler to the BLE thread, Scheduler events will always be one event behind as there are only...
I am attempting to create a packet sniffer for an openthread application. I intend for it to run by sitting on the network and processing all packets with the coap_deafult_handler...
Hello there,
my goal is to wake up via NFC from POWER_OFF Mode (sd_power_system_off). Then right after the nfc wake up sending some information (e.g. UUID) via the NFC...
As a I2C master, I need to be able to read some data from a slave device the length of which I do not know beforehand. First byte I receive from slave is a packet type and...
Hi,
I want to estimate the battery life of my nRF52 device operating on a battery of capacity 800mAh. Device will advertise once in every 10sec with an advertising interval...
I print every 500ms. Here are the last few
timers:INFO:millis 510500, cnt 16728087
timers:INFO:millis 511000, cnt 16744474
timers:INFO:millis 511501, cnt 16760868
timers...
Hello,
I have measured the current consumption of the timer example of SDK13.0.0 with PCA10056.
With timer prescaler set at 16MHz i have 1.28 mA
With timer prescaler...
Hi, I got nRF52 DK PCA10040 device(s132) and follow the steps from devzone.nordicsemi.com/.../ to use arm-none-eabi-gcc(version 5.4) to build examples like blinky. I can successfully...
Hello,
I was wondering whether or not it's possible to achieve a data rate of 160Kbps using BLE4.2. According to what I have read on this nordic blog it should be feasable...
Hello!
I hope this question has not been asked before - at least I can't find it.
I do have an application with two vender specific services (128bit UUID's) and I want...
Hi,
i am doing ble_app_beacon code on nrf 52832 with sdk 11 and s132. the packet, its advertising should only be received by the device whose bluetooth address we are providing...
main.c ble_uart.hex
Hello,
I use nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2.0.0_softdevice configuration to test the ble_uart program.
i use nrfgo Studio to load the...
