Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
I am using nrf52832 chip. I will be receiving time in isoFormat.
I am wondering how convert the iso format to get the date and time in my C program.
I am not using any...
Hi,
I'm develope some sensor with arduino primo, which use nrf52832 as a primary mcu.
I want to measure battery voltage level,and i find some example like:
devzone.nordicsemi...
I am using nrf52832_xxaa with SDK v11.0.
I have a requirement to write into UICR register APPROTECT to set its value to 0x00.
Is it possible?If yes, please provide a sample...
hi,
10040 nrf52dk
softdevice 132 v2.
keil ide
I am trying to read magnetometer values so that i can calibrate it using this method . For this to happen, i need magnetometer...
Hi guys,
I am using FDS module in nrf51822, sdk 11 to store and read data from flash. I have a problem about reading the data. In the documents, the function:
fds_record_open...
The problem
I am trying to build the examples contained in Bluetooth Mesh stack, but I get the following error when running cmake :
...
-- Found assembler: /usr/local...
we tried to configure two gpios as output{two separate controlling switch) at a same time.hex file formed without error but we are executing that hex file on nrf51422 dk board...
Hello folks,
I have been trying to flash/debug an example(blinky_blank_pca200006-nrf51822_xxaa) from nRF SDK installation but to no avail.
The hardware is actually the...
In latest release of MESH SDK v1.0.0, there is support for DFU Bootloader.
It will be helpful, when there is upgrade from firmware side to add new features & remove bugs...
Best way to send datetime from android app to nrf52.
Ultimately I am trying to send two datetimes from android app and compare them with the current time in BLE device...
Hi, I'm using nrf51822 module for bluetooth connectivity in one of my projects. I'm able to compile the code in keil v5 without any errors or warnings. But I'm unable to find...
Hello,
I want to allow users to change the device name as they like. I've been reading about it and I know what needs to be done, i.e. write to the device name characteristic...
i want to add a PA for a nrf51822 chip inorder to extend the coverage. i choosed a PA IC named RFX2401C.i am wondering how to deal with the TX pin and RX pin of RFX2401C.could...
